Edge detector (rising, falling, both) in Verilog - Cheat Sheet & Quick Revision

Recall & Review

beginner

What is a rising edge in digital signals?

A rising edge is when a signal changes from low (0) to high (1). It is like a switch turning on.

beginner

How does a falling edge differ from a rising edge?

A falling edge is when a signal changes from high (1) to low (0). It is like a switch turning off.

beginner

What is the purpose of an edge detector in Verilog?

An edge detector finds when a signal changes state, either rising, falling, or both. It helps circuits react only at those moments.

intermediate

Show a simple Verilog code snippet for detecting a rising edge of a signal 'sig'.

always @(posedge clk) begin prev_sig <= sig; rising_edge_detected <= sig & ~prev_sig; end This code saves the previous signal and checks if current is 1 and previous was 0.

intermediate

How can you detect both rising and falling edges in Verilog?

By comparing the current and previous signal values: - rising edge: current=1 and previous=0 - falling edge: current=0 and previous=1 Detect both by checking if current != previous.

What does a rising edge detector check for in a signal?

A Signal changes from 1 to 0

B Signal changes from 0 to 1

C Signal stays at 1

D Signal stays at 0

A rising edge means the signal goes from low (0) to high (1).

In Verilog, which keyword is used to trigger code on a rising edge of a clock?

A negedge

B always

C edge

D posedge

The 'posedge' keyword triggers on the rising edge of a signal.

How do you detect a falling edge in Verilog?

A current=0 and previous=1

B current=1 and previous=0

C current=previous

D current=1 and previous=1

A falling edge is when the signal changes from 1 to 0.

What does the expression 'sig & ~prev_sig' detect?

A Rising edge

B Both edges

C No change

D Falling edge

It detects when current signal is 1 and previous was 0, a rising edge.

Which condition detects both rising and falling edges?

A current == previous

B current & previous

C current != previous

D ~current & ~previous

If current and previous differ, an edge occurred (rising or falling).

Explain how to detect a rising edge of a signal in Verilog using a previous value register.

Think about saving the signal value each clock and checking if it changed from 0 to 1.

Describe how to detect both rising and falling edges of a signal in Verilog.

Any difference between current and previous means an edge happened.

Practice

1. What does a rising edge detector in Verilog detect?
always @(posedge clk) is often used in such detectors.

easy

A. Both 0 to 1 and 1 to 0 changes

B. A change of signal from 1 to 0

C. A change of signal from 0 to 1

D. No change in signal

Solution

1. Step 1: Understand rising edge meaning

   A rising edge means the signal changes from low (0) to high (1).

2. Step 2: Relate to Verilog edge detection

   The posedge keyword triggers on this rising edge.

3. Final Answer:

   A change of signal from 0 to 1 -> Option C

4. Quick Check:

   Rising edge = 0 to 1 transition [OK]

Hint: Rising edge means signal goes from 0 to 1 [OK]

Common Mistakes:

• Confusing rising edge with falling edge
• Thinking it detects no change
• Mixing up posedge and negedge keywords

2. Which of the following Verilog code snippets correctly detects a falling edge of signal sig?

easy

A. always @(negedge sig) begin // detect falling edge end

B. always @(posedge sig) begin // detect falling edge end

C. always @(sig) begin // detect falling edge end

D. always @(posedge clk) if (sig == 1) // detect falling edge

Solution

1. Step 1: Identify falling edge keyword

   Falling edge detection uses negedge in Verilog.

2. Step 2: Match code to falling edge

   always @(negedge sig) begin // detect falling edge end uses always @(negedge sig), which triggers on signal going from 1 to 0.

3. Final Answer:

   always @(negedge sig) begin // detect falling edge end -> Option A

4. Quick Check:

   Falling edge = negedge keyword [OK]

Hint: Use negedge to detect falling edges in Verilog [OK]

Common Mistakes:

• Using posedge for falling edge detection
• Using level-sensitive sensitivity list
• Confusing signal and clock edges

3. Given this Verilog code snippet for detecting both edges of sig:

reg sig_d;
always @(posedge clk) begin
  sig_d <= sig;
end
wire edge_detect = sig ^ sig_d;

What is the value of edge_detect when sig changes from 0 to 1?

medium

A. 1

B. 0

C. Undefined (X)

D. Remains previous value

Solution

1. Step 1: Understand delayed signal sig_d

   sig_d holds previous clock cycle's sig value.

2. Step 2: Calculate XOR for edge detection

   When sig changes from 0 to 1, XOR with previous 0 gives 1, indicating an edge.

3. Final Answer:

   1 -> Option A

4. Quick Check:

   sig ^ sig_d = 1 on edge [OK]

Hint: XOR current and delayed signal to detect edges [OK]

Common Mistakes:

• Forgetting to delay signal before XOR
• Assuming edge_detect stays 0 on change
• Confusing XOR with AND or OR

4. Identify the error in this Verilog code intended to detect a rising edge of sig:

reg sig_d;
always @(posedge clk) begin
  sig_d <= sig;
end
wire rising_edge = sig & ~sig_d;

medium

A. Using blocking assignment instead of non-blocking

B. Incorrect logic for rising edge detection

C. No sensitivity list for wire rising_edge

D. Missing initial value for sig_d

Solution

1. Step 1: Analyze rising edge logic

   Rising edge is when signal changes from 0 to 1, so previous was 0 and current is 1.

2. Step 2: Check given logic expression

   The expression sig & ~sig_d correctly detects rising edge by current high and previous low.

3. Step 3: Re-examine for errors

   Actually, the logic is correct; the error is elsewhere.

4. Step 4: Identify actual error

   Missing initial value for sig_d can cause unknown behavior at start.

5. Final Answer:

   Missing initial value for sig_d -> Option D

6. Quick Check:

   Initialize delayed signal to avoid unknowns [OK]

Hint: Initialize delayed signals to avoid unknown start values [OK]

Common Mistakes:

• Assuming logic expression is wrong
• Ignoring initial values for registers
• Confusing blocking and non-blocking assignments

5. You want to design a Verilog module that outputs a pulse of 1 clock cycle width whenever sig changes either from 0 to 1 or 1 to 0. Which code snippet correctly implements this?

hard

A. reg sig_d;
always @(posedge clk) sig_d <= sig;
wire edge_pulse = sig & ~sig_d;

B. reg sig_d;
always @(posedge clk) sig_d <= sig;
wire edge_pulse = sig ^ sig_d;

C. wire edge_pulse = (sig == 1) ? 1 : 0;

D. always @(posedge sig) edge_pulse = 1;

Solution

1. Step 1: Understand requirement for both edges

   The pulse should be high for one clock cycle on any signal change (rising or falling).

2. Step 2: Analyze each option

   reg sig_d; always @(posedge clk) sig_d <= sig; wire edge_pulse = sig ^ sig_d; uses XOR between current and delayed signal, which is 1 only on change, producing a 1-cycle pulse.

3. Step 3: Confirm other options

   reg sig_d; always @(posedge clk) sig_d <= sig; wire edge_pulse = sig & ~sig_d; detects only rising edge; C is level detection; D triggers on posedge of sig, not clock, and lacks pulse width control.

4. Final Answer:

   reg sig_d; always @(posedge clk) sig_d <= sig; wire edge_pulse = sig ^ sig_d; -> Option B

5. Quick Check:

   XOR current and delayed signal for both edges pulse [OK]

Hint: XOR current and delayed signals for both edges pulse [OK]

Common Mistakes:

• Using only rising edge logic for both edges
• Triggering on signal edge instead of clock
• Not producing single clock cycle pulse