Module instantiation syntax in Verilog

Introduction

Module instantiation lets you use one design inside another. It helps build bigger circuits from smaller parts.

When you want to reuse a design block multiple times in a bigger design.

When you want to organize your code by breaking it into smaller modules.

When you want to connect different parts of a circuit together.

When you want to test a module inside a testbench.

When you want to build hierarchical designs with multiple levels.

Syntax

Verilog

module_name instance_name (port_connections);

// or with named ports
module_name instance_name (
  .port1(signal1),
  .port2(signal2),
  ...
);

The module_name is the name of the module you want to use.

The instance_name is a unique name for this copy of the module.

Examples

Instantiates an adder module with ports connected by order.

Verilog

adder my_adder (a, b, sum);

Instantiates an adder module with ports connected by name for clarity.

Verilog

adder my_adder (
  .input1(a),
  .input2(b),
  .output_sum(sum)
);

Instantiates a counter module named cnt1 with ordered ports.

Verilog

counter cnt1 (clk, reset, count);

Sample Program

This program defines a simple adder module and uses module instantiation to include it inside a top module. It changes inputs and shows the sum output.

Verilog

module adder(input wire a, input wire b, output wire sum);
  assign sum = a ^ b; // corrected to XOR for 1-bit addition without carry
endmodule

module top;
  reg a, b;
  wire sum;

  adder my_adder(.a(a), .b(b), .sum(sum));

  initial begin
    a = 1'b0; b = 1'b0;
    #10 a = 1'b1; b = 1'b0;
    #10 a = 1'b1; b = 1'b1;
    #10 $finish;
  end

  initial begin
    $monitor("At time %0t: a=%b b=%b sum=%b", $time, a, b, sum);
  end
endmodule

Important Notes

Using named port connections helps avoid mistakes when ports change order.

Each instance name must be unique inside the parent module.

Module instantiation is like plugging a smaller circuit into a bigger one.

Summary

Module instantiation lets you reuse and connect modules inside other modules.

You can connect ports by order or by name; named connections are safer.

Each instance needs a unique name to avoid confusion.

Practice

1.

What is the main purpose of module instantiation in Verilog?

easy

A. To declare variables inside a module

B. To reuse and connect modules inside other modules

C. To write comments in the code

D. To define the clock frequency

Solution

1. Step 1: Understand module instantiation concept

   Module instantiation allows you to use one module inside another, making design reusable.

2. Step 2: Identify the correct purpose

   Among the options, only reusing and connecting modules matches the purpose of instantiation.

3. Final Answer:

   To reuse and connect modules inside other modules -> Option B

4. Quick Check:

   Module instantiation = reuse modules [OK]

Hint: Module instantiation = reuse modules inside others [OK]

Common Mistakes:

• Confusing instantiation with variable declaration
• Thinking instantiation is for comments
• Mixing instantiation with clock setup

2.

Which of the following is the correct syntax for instantiating a module named adder with ports a, b, and sum using named port connections?

module adder(input a, input b, output sum); ... endmodule

easy

A. adder my_adder(a, b, sum);

B. my_adder adder(.a(a), .b(b), .sum(sum));

C. adder(.a=a, .b=b, .sum=sum) my_adder;

D. adder my_adder(.a(a), .b(b), .sum(sum));

Solution

1. Step 1: Recall named port connection syntax

   Named connections use dot before port name and parentheses for signal, like .port(signal).

2. Step 2: Check instance name placement

   The instance name comes after the module name, so adder my_adder(...); is correct.

3. Final Answer:

   adder my_adder(.a(a), .b(b), .sum(sum)); -> Option D

4. Quick Check:

   ModuleName InstanceName(.port(signal)) [OK]

Hint: Instance name follows module name; use .port(signal) for named ports [OK]

Common Mistakes:

• Placing instance name before module name
• Using = instead of parentheses in port connections
• Omitting instance name

3.

Given the module and instantiation below, what is the value of out after simulation?

module inverter(input in, output out); assign out = ~in; endmodule

module top; reg a = 1'b0; wire b; inverter inv1(.in(a), .out(b)); endmodule

medium

A. b = 1'b1

B. b is undefined

C. Syntax error due to missing semicolon

D. b = 1'b0

Solution

1. Step 1: Understand inverter module behavior

   The inverter outputs the bitwise NOT of input in. If in is 0, output is 1.

2. Step 2: Check input value and connection

   Input a is initialized to 0, connected to inverter input in. So output b = ~0 = 1.

3. Final Answer:

   b = 1'b1 -> Option A

4. Quick Check:

   ~0 = 1, so output = 1 [OK]

Hint: Inverter flips input bit; 0 becomes 1 [OK]

Common Mistakes:

• Confusing input and output signals
• Assuming output equals input
• Missing initial value for input

4.

Identify the error in the following module instantiation:

module counter(input clk, output reg [3:0] count); ... endmodule

module top; wire clk; wire [3:0] cnt; counter cnt_inst(clk, cnt); counter cnt_inst(clk, cnt); endmodule

medium

A. Incorrect port connection order

B. Missing semicolon after module declaration

C. Duplicate instance name 'cnt_inst' used

D. Output port declared as wire instead of reg

Solution

1. Step 1: Check instance names in top module

   Two instances named cnt_inst are declared, which is not allowed.

2. Step 2: Verify other syntax elements

   Semicolons and port order appear correct; output port type mismatch is allowed since output is connected to wire.

3. Final Answer:

   Duplicate instance name 'cnt_inst' used -> Option C

4. Quick Check:

   Instance names must be unique [OK]

Hint: Each instance needs a unique name [OK]

Common Mistakes:

• Using same instance name twice
• Confusing port order with named connections
• Thinking output port must be reg in top

5.

You want to instantiate a module mux2to1 twice inside a top module, connecting inputs a, b, select sel, and outputs out1, out2. Which is the correct way to instantiate both with unique instance names and named port connections?

hard

A. mux2to1 mux1(.a(a), .b(b), .sel(sel), .out(out1)); mux2to1 mux2(.a(a), .b(b), .sel(sel), .out(out2));

B. mux2to1 mux1(.a(a), .b(b), .sel(sel), .out(out1)), mux2to1 mux2(.a(a), .b(b), .sel(sel), .out(out2));

C. mux2to1(.a(a), .b(b), .sel(sel), .out(out1)) mux1; mux2to1(.a(a), .b(b), .sel(sel), .out(out2)) mux2;

D. mux2to1 mux1(a, b, sel, out1); mux2to1 mux1(a, b, sel, out2);

Solution

1. Step 1: Confirm named port connection syntax

   Named ports use dot before port name and parentheses around signal, e.g., .a(a).

2. Step 2: Check instance names and separation

   Each instance must have a unique name and be separated by semicolons.

3. Step 3: Validate options

   mux2to1 mux1(.a(a), .b(b), .sel(sel), .out(out1)); mux2to1 mux2(.a(a), .b(b), .sel(sel), .out(out2)); correctly names instances mux1 and mux2, uses named ports, and separates with semicolons.

4. Final Answer:

   mux2to1 mux1(.a(a), .b(b), .sel(sel), .out(out1)); mux2to1 mux2(.a(a), .b(b), .sel(sel), .out(out2)); -> Option A

5. Quick Check:

   Unique instance names + named ports + semicolons = correct [OK]

Hint: Use unique instance names and semicolons between instantiations [OK]

Common Mistakes:

• Using same instance name twice
• Separating instances with commas instead of semicolons
• Placing instance name after port list