Multiplexer design in Verilog - Cheat Sheet & Quick Revision

Recall & Review

beginner

What is a multiplexer (MUX) in digital design?

A multiplexer is a device that selects one input from many inputs and forwards it to a single output line based on select signals.

beginner

How many select lines are needed for a 4-to-1 multiplexer?

Two select lines are needed because 2 bits can represent 4 different combinations (00, 01, 10, 11).

intermediate

Write the Verilog module header for a 4-to-1 multiplexer with 4 inputs, 2 select lines, and 1 output.

module mux4to1(input wire [3:0] in, input wire [1:0] sel, output wire out);

intermediate

What is the role of the 'case' statement in a multiplexer Verilog design?

The 'case' statement selects which input to assign to the output based on the select lines, making the code clear and easy to read.

beginner

Explain why multiplexers are useful in digital circuits.

Multiplexers help reduce the number of wires needed by selecting one input to pass through, enabling efficient data routing and saving hardware resources.

How many inputs does a 2-to-1 multiplexer have?

A 2

B 1

C 4

D 3

A 2-to-1 multiplexer has exactly 2 inputs and 1 output.

What does the select line do in a multiplexer?

A Controls the output voltage

B Controls which input is sent to the output

C Increases the number of inputs

D Acts as an output

The select line chooses which input is connected to the output.

In Verilog, which statement is commonly used to implement a multiplexer?

A case

B if-else

C for loop

D while loop

The 'case' statement is often used to select inputs based on select lines.

How many select lines are needed for an 8-to-1 multiplexer?

A 1

B 2

C 4

D 3

3 select lines can represent 8 combinations (2^3 = 8).

What is the output of a multiplexer when select lines are set to 10 (binary) in a 4-to-1 MUX?

A Input 1

B Input 2

C Input 3

D Input 0

Binary 10 corresponds to decimal 2, so input 2 is selected.

Describe how a 4-to-1 multiplexer works and how select lines control the output.

Think about how binary numbers on select lines pick one input.

Write a simple Verilog code snippet for a 2-to-1 multiplexer using a case statement.

Use 'case(sel)' to choose between inputs.

Practice

1. What is the main purpose of a multiplexer in Verilog design?

easy

A. To select one input from multiple inputs based on selector signals

B. To store data temporarily

C. To perform arithmetic operations

D. To generate clock signals

Solution

1. Step 1: Understand the function of a multiplexer

   A multiplexer routes one of many inputs to a single output based on selector signals.

2. Step 2: Compare with other options

   Other options describe functions unrelated to multiplexers, like storage or arithmetic.

3. Final Answer:

   To select one input from multiple inputs based on selector signals -> Option A

4. Quick Check:

   Multiplexer = Select input [OK]

Hint: Multiplexer chooses one input out of many [OK]

Common Mistakes:

• Confusing multiplexer with memory elements
• Thinking it performs calculations
• Mixing it up with clock generators

2. Which of the following is the correct syntax to define a 2-to-1 multiplexer using a conditional operator in Verilog?

easy

A. assign out = in0 ? sel : in1;

B. assign out = sel & in1 | in0;

C. assign out = sel ? in1 : in0;

D. assign out = sel | in1 & in0;

Solution

1. Step 1: Recall conditional operator syntax

   The conditional operator in Verilog is: condition ? true_value : false_value.

2. Step 2: Match syntax to multiplexer logic

   For a 2-to-1 mux, output is in1 if sel=1, else in0. So, assign out = sel ? in1 : in0; is correct.

3. Final Answer:

   assign out = sel ? in1 : in0; -> Option C

4. Quick Check:

   Conditional operator = condition ? true : false [OK]

Hint: Use condition ? true_val : false_val for mux [OK]

Common Mistakes:

• Using bitwise operators instead of conditional
• Swapping true and false values
• Incorrect operator precedence

3. What is the output of this Verilog code snippet for a 4-to-1 multiplexer when sel = 2'b10 and inputs are in0=0, in1=1, in2=1, in3=0?

module mux4to1(output reg out, input [1:0] sel, input in0, in1, in2, in3);
  always @(*) begin
    case(sel)
      2'b00: out = in0;
      2'b01: out = in1;
      2'b10: out = in2;
      2'b11: out = in3;
    endcase
  end
endmodule

medium

A. 0

B. Error

C. Undefined

D. 1

Solution

1. Step 1: Identify selected input based on sel

   sel = 2'b10 selects input in2 according to the case statement.

2. Step 2: Check value of in2

   in2 is given as 1, so output out = 1.

3. Final Answer:

   1 -> Option D

4. Quick Check:

   sel=2'b10 selects in2=1 [OK]

Hint: Match sel bits to input index [OK]

Common Mistakes:

• Confusing binary selector values
• Ignoring case statement mapping
• Assuming default output without case

4. Identify the error in this Verilog 2-to-1 multiplexer code:

module mux2to1(output reg out, input sel, input in0, in1);
  always @(*) begin
    if (sel == 1) out = in1;
    else if (sel == 0) out = in0;
    else out = 1'bx;
  end
endmodule

medium

A. Using 'else if' instead of 'else' for sel check

B. No default case needed for 1-bit sel

C. Output should be wire, not reg

D. Missing sensitivity list in always block

Solution

1. Step 1: Analyze selector signal type

   sel is 1-bit, so it can only be 0 or 1, no other values possible.

2. Step 2: Check necessity of default case

   Since sel cannot be other than 0 or 1, the 'else out = 1'bx;' is unnecessary.

3. Final Answer:

   No default case needed for 1-bit sel -> Option B

4. Quick Check:

   1-bit sel only 0 or 1, no default needed [OK]

Hint: 1-bit selector has only two values [OK]

Common Mistakes:

• Adding unreachable default cases
• Confusing reg and wire for outputs
• Forgetting sensitivity list is @(*)

5. You need to design an 8-to-1 multiplexer in Verilog using a case statement. Which of the following code snippets correctly implements this multiplexer assuming inputs in0 to in7, selector sel[2:0], and output out?

hard

A. always @(*) begin
case(sel)
3'b000: out = in0;
3'b001: out = in1;
3'b010: out = in2;
3'b011: out = in3;
3'b100: out = in4;
3'b101: out = in5;
3'b110: out = in6;
3'b111: out = in7;
default: out = 1'b0;
endcase
end

B. always @(sel) begin
if(sel == 0) out = in0;
else if(sel == 1) out = in1;
else if(sel == 2) out = in2;
else if(sel == 3) out = in3;
else if(sel == 4) out = in4;
else if(sel == 5) out = in5;
else if(sel == 6) out = in6;
else if(sel == 7) out = in7;
end

C. always @(*) begin
case(sel)
3'b000: out = in7;
3'b001: out = in6;
3'b010: out = in5;
3'b011: out = in4;
3'b100: out = in3;
3'b101: out = in2;
3'b110: out = in1;
3'b111: out = in0;
endcase
end

D. always @(*) begin
case(sel)
3'b000: out = in0;
3'b001: out = in1;
3'b010: out = in2;
3'b011: out = in3;
3'b100: out = in4;
3'b101: out = in5;
3'b110: out = in6;
endcase
end

Solution

1. Step 1: Check completeness of case statement

   always @(*) begin case(sel) 3'b000: out = in0; 3'b001: out = in1; 3'b010: out = in2; 3'b011: out = in3; 3'b100: out = in4; 3'b101: out = in5; 3'b110: out = in6; 3'b111: out = in7; default: out = 1'b0; endcase end covers all 8 selector values (0 to 7) and includes a default case.

2. Step 2: Verify correct input mapping

   always @(*) begin case(sel) 3'b000: out = in0; 3'b001: out = in1; 3'b010: out = in2; 3'b011: out = in3; 3'b100: out = in4; 3'b101: out = in5; 3'b110: out = in6; 3'b111: out = in7; default: out = 1'b0; endcase end maps sel values 3'b000 to 3'b111 to in0 through in7 respectively, which is correct.

3. Step 3: Identify issues in other options

   always @(sel) begin if(sel == 0) out = in0; else if(sel == 1) out = in1; else if(sel == 2) out = in2; else if(sel == 3) out = in3; else if(sel == 4) out = in4; else if(sel == 5) out = in5; else if(sel == 6) out = in6; else if(sel == 7) out = in7; end uses if-else but sensitivity list is only sel, which is acceptable but lacks default. always @(*) begin case(sel) 3'b000: out = in7; 3'b001: out = in6; 3'b010: out = in5; 3'b011: out = in4; 3'b100: out = in3; 3'b101: out = in2; 3'b110: out = in1; 3'b111: out = in0; endcase end reverses input mapping incorrectly. always @(*) begin case(sel) 3'b000: out = in0; 3'b001: out = in1; 3'b010: out = in2; 3'b011: out = in3; 3'b100: out = in4; 3'b101: out = in5; 3'b110: out = in6; endcase end misses case for 3'b111.

4. Final Answer:

   Option A correctly implements 8-to-1 mux with case and default -> Option A

5. Quick Check:

   Complete case with all inputs mapped = always @(*) begin case(sel) 3'b000: out = in0; 3'b001: out = in1; 3'b010: out = in2; 3'b011: out = in3; 3'b100: out = in4; 3'b101: out = in5; 3'b110: out = in6; 3'b111: out = in7; default: out = 1'b0; endcase end [OK]

Hint: Cover all selector values with case and default [OK]

Common Mistakes:

• Missing cases for some selector values
• Incorrect input to selector mapping
• No default case in case statement