Comparator design in Verilog

Introduction

A comparator checks which number is bigger or if they are equal. It helps decisions in digital circuits.

To compare two sensor values and choose the higher one.

To check if a signal is above a certain threshold.

To decide which of two inputs is greater in a calculator circuit.

To control a traffic light based on car counts from two roads.

Syntax

Verilog

module comparator #(
  parameter N = 4
)(
  input [N-1:0] a, b,
  output reg gt, lt, eq
);
  always @(*) begin
    if (a > b) begin
      gt = 1; lt = 0; eq = 0;
    end else if (a < b) begin
      gt = 0; lt = 1; eq = 0;
    end else begin
      gt = 0; lt = 0; eq = 1;
    end
  end
endmodule

a and b are the numbers to compare.

gt, lt, and eq show if a is greater, less, or equal to b.

Examples

This compares two 4-bit numbers and sets outputs accordingly.

Verilog

module comparator_4bit(
  input [3:0] a, b,
  output reg gt, lt, eq
);
  always @(*) begin
    if (a > b) begin
      gt = 1; lt = 0; eq = 0;
    end else if (a < b) begin
      gt = 0; lt = 1; eq = 0;
    end else begin
      gt = 0; lt = 0; eq = 1;
    end
  end
endmodule

This compares two single-bit inputs.

Verilog

module comparator_1bit(
  input a, b,
  output reg gt, lt, eq
);
  always @(*) begin
    if (a > b) begin
      gt = 1; lt = 0; eq = 0;
    end else if (a < b) begin
      gt = 0; lt = 1; eq = 0;
    end else begin
      gt = 0; lt = 0; eq = 1;
    end
  end
endmodule

Sample Program

This test program compares three pairs of 4-bit numbers and prints which is greater, less, or equal.

Verilog

module test_comparator;
  reg [3:0] a, b;
  wire gt, lt, eq;

  comparator_4bit comp(.a(a), .b(b), .gt(gt), .lt(lt), .eq(eq));

  initial begin
    a = 4'd9; b = 4'd5;
    #10;
    $display("a=%d b=%d gt=%b lt=%b eq=%b", a, b, gt, lt, eq);

    a = 4'd3; b = 4'd7;
    #10;
    $display("a=%d b=%d gt=%b lt=%b eq=%b", a, b, gt, lt, eq);

    a = 4'd4; b = 4'd4;
    #10;
    $display("a=%d b=%d gt=%b lt=%b eq=%b", a, b, gt, lt, eq);

    $finish;
  end
endmodule

module comparator_4bit(
  input [3:0] a, b,
  output reg gt, lt, eq
);
  always @(*) begin
    if (a > b) begin
      gt = 1; lt = 0; eq = 0;
    end else if (a < b) begin
      gt = 0; lt = 1; eq = 0;
    end else begin
      gt = 0; lt = 0; eq = 1;
    end
  end
endmodule

Important Notes

Use always @(*) to update outputs whenever inputs change.

Make sure output signals are declared as reg because they change inside always block.

Summary

A comparator checks if one number is greater, less, or equal to another.

It uses simple if-else conditions inside an always block.

Outputs tell the result clearly with separate signals.

Practice

1.

What is the main purpose of a comparator in Verilog?

easy

A. To store data temporarily

B. To check if one number is greater, less, or equal to another

C. To add two numbers together

D. To generate clock signals

Solution

1. Step 1: Understand comparator function

   A comparator compares two values to determine their relationship.

2. Step 2: Identify correct purpose

   Only To check if one number is greater, less, or equal to another describes comparing numbers, which is the comparator's job.

3. Final Answer:

   To check if one number is greater, less, or equal to another -> Option B

4. Quick Check:

   Comparator = Compare numbers [OK]

Hint: Comparator compares values, not adds or stores [OK]

Common Mistakes:

• Confusing comparator with adder
• Thinking comparator stores data
• Mixing comparator with clock generator

2.

Which of the following is the correct way to start an always block for a comparator that reacts to changes in inputs a and b?

easy

A. always @(a, b) begin

B. always @(posedge clk) begin

C. always @(a and b) begin

D. always @(a or b) begin

Solution

1. Step 1: Understand sensitivity list syntax

   In Verilog, sensitivity list uses 'or' to list signals that trigger the block.

2. Step 2: Check options

   always @(a or b) begin uses 'or' correctly. always @(a, b) begin uses comma which is not valid in Verilog sensitivity lists.

3. Final Answer:

   always @(a or b) begin -> Option D

4. Quick Check:

   Sensitivity list uses 'or' between signals [OK]

Hint: Use 'or' between signals in sensitivity list [OK]

Common Mistakes:

• Using commas instead of 'or' in sensitivity list
• Using 'and' instead of 'or'
• Using clock edge when not needed

3.

Given the following Verilog code snippet, what will be the output signals gt, lt, and eq if a = 5 and b = 3?

module comp(input [3:0] a, b, output reg gt, lt, eq);
  always @(a or b) begin
    if (a > b) begin
      gt = 1; lt = 0; eq = 0;
    end else if (a < b) begin
      gt = 0; lt = 1; eq = 0;
    end else begin
      gt = 0; lt = 0; eq = 1;
    end
  end
endmodule

medium

A. gt=0, lt=0, eq=1

B. gt=0, lt=1, eq=0

C. gt=1, lt=0, eq=0

D. gt=1, lt=1, eq=0

Solution

1. Step 1: Compare values a=5 and b=3

   Since 5 is greater than 3, the condition 'a > b' is true.

2. Step 2: Determine output signals

   For 'a > b', gt=1, lt=0, eq=0 as per code.

3. Final Answer:

   gt=1, lt=0, eq=0 -> Option C

4. Quick Check:

   5 > 3 means gt=1 [OK]

Hint: Check which condition is true first [OK]

Common Mistakes:

• Mixing up greater than and less than
• Setting multiple outputs to 1 incorrectly
• Ignoring else conditions

4.

Identify the error in this comparator code snippet:

module comp(input [3:0] a, b, output reg gt, lt, eq);
  always @(a, b) begin
    if (a > b)
      gt = 1; lt = 0; eq = 0;
    else if (a < b)
      gt = 0; lt = 1; eq = 0;
    else
      gt = 0; lt = 0; eq = 1;
  end
endmodule

medium

A. Missing begin-end blocks after if and else if

B. Incorrect sensitivity list syntax

C. Output signals should be wires, not regs

D. Using non-blocking assignments instead of blocking

Solution

1. Step 1: Check if-else statement structure

   Multiple statements after if need to be grouped with begin-end blocks.

2. Step 2: Identify missing begin-end

   Here, multiple assignments after if and else if lack begin-end, causing syntax errors.

3. Final Answer:

   Missing begin-end blocks after if and else if -> Option A

4. Quick Check:

   Multiple statements need begin-end [OK]

Hint: Use begin-end for multiple statements in if blocks [OK]

Common Mistakes:

• Forgetting begin-end with multiple statements
• Confusing sensitivity list syntax
• Wrong data type for outputs

5.

You want to design a 4-bit comparator that sets gt high if a > b, lt high if a < b, and eq high if equal. However, you also want to ignore the comparison if either a or b is zero (all bits zero), setting all outputs low in that case. Which Verilog code snippet correctly implements this?

hard

A. always @(a or b) begin
if (a == 0 || b == 0) begin
gt = 0; lt = 0; eq = 0;
end else if (a > b) begin
gt = 1; lt = 0; eq = 0;
end else if (a < b) begin
gt = 0; lt = 1; eq = 0;
end else begin
gt = 0; lt = 0; eq = 1;
end
end

B. always @(a or b) begin
if (a == 0 && b == 0) begin
gt = 0; lt = 0; eq = 0;
end else if (a > b) begin
gt = 1; lt = 0; eq = 0;
end else if (a < b) begin
gt = 0; lt = 1; eq = 0;
end else begin
gt = 0; lt = 0; eq = 1;
end
end

C. always @(a or b) begin
if (a != 0 && b != 0) begin
if (a > b) begin
gt = 1; lt = 0; eq = 0;
end else if (a < b) begin
gt = 0; lt = 1; eq = 0;
end else begin
gt = 0; lt = 0; eq = 1;
end
end else begin
gt = 0; lt = 0; eq = 0;
end
end

D. always @(a or b) begin
if (a == 0 || b == 0) begin
gt = 1; lt = 1; eq = 1;
end else if (a > b) begin
gt = 1; lt = 0; eq = 0;
end else if (a < b) begin
gt = 0; lt = 1; eq = 0;
end else begin
gt = 0; lt = 0; eq = 1;
end
end

Solution

1. Step 1: Understand the zero check condition

   The requirement is to ignore comparison if either a or b is zero, so use 'a == 0 || b == 0'.

2. Step 2: Verify output assignments

   always @(a or b) begin if (a == 0 || b == 0) begin gt = 0; lt = 0; eq = 0; end else if (a > b) begin gt = 1; lt = 0; eq = 0; end else if (a < b) begin gt = 0; lt = 1; eq = 0; end else begin gt = 0; lt = 0; eq = 1; end end sets all outputs low when either input is zero, then compares normally otherwise.

3. Final Answer:

   Option A code snippet -> Option A

4. Quick Check:

   Use '||' to check either zero, outputs low [OK]

Hint: Use '||' to check either zero, set outputs low [OK]

Common Mistakes:

• Using '&&' instead of '||' for zero check
• Setting outputs high when inputs are zero
• Not handling zero inputs separately