Under-defined vs fully-defined vs over-defined in Solidworks - Formula Comparison Trace

Sample Data

This data shows different sketch elements in SolidWorks with their applied constraints and resulting definition status.

Cell	Value
A1	Sketch Element
B1	Constraints Applied
C1	Status
A2	Line 1
B2	Length only
C2	Under-defined
A3	Rectangle
B3	Length, Width, Horizontal & Vertical constraints
C3	Fully-defined
A4	Circle
B4	Radius, Center fixed, Extra coincident constraint
C4	Over-defined

Formula Trace

Status = IF(Constraints < Required, "Under-defined", IF(Constraints = Required, "Fully-defined", "Over-defined"))

Step 1: Check constraints for Line 1: Length only

Step 2: Check constraints for Rectangle: Length, Width, Horizontal & Vertical constraints

Step 3: Check constraints for Circle: Radius, Center fixed, Extra coincident constraint

Cell Reference Map

   A           B                          C
1 Sketch    Constraints Applied         Status
2 Line 1    Length only                Under-defined
3 Rectangle Length, Width, Horizontal & Vertical constraints Fully-defined
4 Circle    Radius, Center fixed, Extra coincident constraint Over-defined

Cells A2:C4 are referenced to determine the status of each sketch element based on constraints.

Result

   A           B                          C
1 Sketch    Constraints Applied         Status
2 Line 1    Length only                Under-defined
3 Rectangle Length, Width, Horizontal & Vertical constraints Fully-defined
4 Circle    Radius, Center fixed, Extra coincident constraint Over-defined

The final status column shows if each sketch element is under-defined, fully-defined, or over-defined based on constraints.

Sheet Trace Quiz - 3 Questions

What status does a sketch have if it has fewer constraints than required?

A Fully-defined

B Under-defined

C Over-defined

D Undefined

Key Result

Status depends on comparing applied constraints to required constraints: less means under-defined, equal means fully-defined, more means over-defined.

Practice

1.

Which of the following best describes a fully-defined sketch in SolidWorks?

easy

A. The sketch has conflicting constraints causing errors.

B. The sketch has too few constraints and can still move or change.

C. The sketch is missing all constraints and is free to move.

D. The sketch has just enough constraints to fix its position and shape.

Solution

1. Step 1: Understand sketch constraint types

   Under-defined means not enough constraints, fully-defined means just enough, and over-defined means too many constraints causing conflicts.

2. Step 2: Identify fully-defined sketch meaning

   A fully-defined sketch is fixed in place with no degrees of freedom left, meaning it has just enough constraints.

3. Final Answer:

   The sketch has just enough constraints to fix its position and shape. -> Option D

4. Quick Check:

   Fully-defined = just right constraints [OK]

Hint: Fully-defined means no movement possible [OK]

Common Mistakes:

• Confusing fully-defined with over-defined
• Thinking fully-defined means no constraints
• Assuming under-defined is fixed

2.

Which of these constraint sets will cause a sketch to be over-defined?

1. Horizontal line fixed length
2. Horizontal line fixed length + another length constraint on same line
3. Vertical line with one length constraint
4. Circle with radius constraint only

easy

A. Option 3 only

B. Option 2 only

C. Option 4 only

D. Option 1 only

Solution

1. Step 1: Analyze constraints for over-definition

   Over-defined means conflicting or redundant constraints. Option 2 has two length constraints on the same line, causing conflict.

2. Step 2: Check other options

   Options 1, 3, and 4 have only one constraint per element, so they are not over-defined.

3. Final Answer:

   Option 2 only -> Option B

4. Quick Check:

   Multiple conflicting constraints = over-defined [OK]

Hint: Two constraints on same element cause over-defined [OK]

Common Mistakes:

• Thinking one constraint is over-defined
• Confusing under-defined with over-defined
• Ignoring conflicting constraints

3.

Given a sketch with a rectangle where only two adjacent sides have length constraints and no other constraints, what is the sketch state?

medium

A. Under-defined

B. Fixed

C. Over-defined

D. Fully-defined

Solution

1. Step 1: Identify constraints on rectangle

   Two adjacent sides have length constraints, but no position or angle constraints are given.

2. Step 2: Determine sketch freedom

   Without fixing position or angles, the rectangle can still move or rotate, so it is under-defined.

3. Final Answer:

   Under-defined -> Option A

4. Quick Check:

   Not enough constraints = under-defined [OK]

Hint: Missing position constraints means under-defined [OK]

Common Mistakes:

• Assuming length constraints alone fully define sketch
• Confusing fixed with fully-defined
• Ignoring degrees of freedom like rotation

4.

Look at this sketch constraint setup:

1. A line fixed length 50mm
2. Another length constraint 60mm on the same line
3. Horizontal constraint on the line

What is the problem and how to fix it?

medium

A. Over-defined due to conflicting length constraints; remove one length constraint.

B. Under-defined because horizontal constraint is missing; add horizontal constraint.

C. Fully-defined; no problem exists.

D. Over-defined due to missing horizontal constraint; add horizontal constraint.

Solution

1. Step 1: Identify conflicting constraints

   The line has two different length constraints (50mm and 60mm), which conflict and cause over-definition.

2. Step 2: Fix by removing conflict

   Removing one length constraint resolves the conflict and fixes the over-defined state.

3. Final Answer:

   Over-defined due to conflicting length constraints; remove one length constraint. -> Option A

4. Quick Check:

   Conflicting constraints cause over-defined [OK]

Hint: Remove conflicting constraints to fix over-defined [OK]

Common Mistakes:

• Adding more constraints instead of removing
• Ignoring conflicting lengths
• Assuming horizontal constraint fixes over-definition

5.

You have a sketch of a triangle with all three sides length constrained and one angle constrained between two sides. The sketch still shows as under-defined. What could be the reason?

hard

A. The sketch is over-defined due to too many constraints on sides.

B. The angle constraint conflicts with side lengths causing errors.

C. The triangle can still move or rotate because position constraints are missing.

D. All constraints fully define the sketch; this is a software bug.

Solution

1. Step 1: Analyze given constraints

   All sides have length constraints and one angle is fixed, but no constraints fix the triangle's position in the plane.

2. Step 2: Understand under-defined cause

   Without fixing position (like fixing a point or adding horizontal/vertical constraints), the sketch can still move or rotate, so it remains under-defined.

3. Final Answer:

   The triangle can still move or rotate because position constraints are missing. -> Option C

4. Quick Check:

   Missing position constraints cause under-defined [OK]

Hint: Fix position to fully define sketch [OK]

Common Mistakes:

• Assuming side lengths alone fully define sketch
• Confusing over-defined with under-defined
• Ignoring need for position constraints