Star-delta starter using timers in PLC Programming - Cheat Sheet & Quick Revision

Recall & Review

beginner

What is the main purpose of a star-delta starter in motor control?

A star-delta starter reduces the starting current of a motor by initially connecting the motor windings in a star configuration, then switching to a delta configuration after the motor reaches a certain speed.

beginner

Which timer types are commonly used in PLC programming for star-delta starters?

On-delay timers are commonly used to control the time delay between star and delta connections in a star-delta starter.

intermediate

In a star-delta starter PLC program, what happens when the star timer finishes its preset time?

When the star timer finishes, the PLC turns off the star contactor and turns on the delta contactor to switch the motor windings from star to delta connection.

intermediate

Why is it important to have an off delay or interlock between star and delta contactors?

To prevent both star and delta contactors from being on at the same time, which can cause a short circuit or motor damage.

beginner

What is the typical sequence of operations in a star-delta starter using timers?

1. Start command energizes star contactor and timer starts.
2. After timer delay, star contactor de-energizes.
3. Delta contactor energizes to run motor in delta.
4. Motor runs normally until stop command.

What does the star connection do in a star-delta starter?

A Reduces starting current

B Increases motor speed

C Switches motor off

D Connects motor to power supply

The star connection reduces the starting current by connecting motor windings in a way that lowers voltage per winding.

Which timer is used to delay switching from star to delta in PLC programming?

A Off-delay timer

B On-delay timer

C Retentive timer

D Pulse timer

An on-delay timer waits a preset time after activation before switching from star to delta.

What is the risk if star and delta contactors are energized simultaneously?

A Short circuit or motor damage

B Motor runs faster

C No effect

D Motor stops immediately

Simultaneous energizing causes a short circuit, risking damage to the motor and starter.

In a star-delta starter, when does the delta contactor energize?

A Before star contactor

B At motor stop

C After star timer finishes

D Simultaneously with star contactor

The delta contactor energizes after the star timer finishes to switch motor windings to delta.

What is the first step in the star-delta starter sequence?

A Switch off power supply

B Energize delta contactor

C Stop motor

D Energize star contactor and start timer

The first step is to energize the star contactor and start the timer to reduce starting current.

Explain the working principle of a star-delta starter using timers in a PLC program.

Think about how the motor starts gently and then runs normally.

Describe the safety considerations when programming a star-delta starter with timers.

Focus on what can go wrong if contactors are on together.

Practice

1. What is the main purpose of using timers in a star-delta starter circuit?

easy

A. To control the time the motor stays connected in star and delta modes

B. To increase the motor speed instantly

C. To change the motor direction automatically

D. To measure the motor temperature

Solution

1. Step 1: Understand star-delta starter function

   The star-delta starter reduces starting current by initially connecting the motor in star mode, then switching to delta mode.

2. Step 2: Role of timers in this process

   Timers control how long the motor stays in star mode before switching to delta mode to ensure smooth transition and reduce electrical stress.

3. Final Answer:

   To control the time the motor stays connected in star and delta modes -> Option A

4. Quick Check:

   Timers control connection time = A [OK]

Hint: Timers manage star and delta connection duration [OK]

Common Mistakes:

• Thinking timers increase motor speed
• Confusing timers with direction control
• Assuming timers measure temperature

2. Which of the following is the correct way to declare a timer in a PLC program for star-delta starting?

easy

A. TIMER Timer1 (START=Start, TIME=5s, DONE=Done)

B. TON Timer1 (IN:=Start, PT:=T#5s, Q=>Done)

C. TON Timer1(IN:=Start, PT:=T#5s, Q=>Done);

D. Timer1 = TON(Start, 5)

Solution

1. Step 1: Identify correct timer syntax in PLC

   In IEC 61131-3 standard, TON timers are declared with input IN, preset time PT, and output Q using := and => operators.

2. Step 2: Compare options

   TON Timer1 (IN:=Start, PT:=T#5s, Q=>Done) uses correct syntax: TON Timer1 (IN:=Start, PT:=T#5s, Q=>Done). Others have syntax errors or incorrect format.

3. Final Answer:

   TON Timer1 (IN:=Start, PT:=T#5s, Q=>Done) -> Option B

4. Quick Check:

   Correct IEC timer syntax = B [OK]

Hint: Use TON with IN:=, PT:=, Q=> for timers [OK]

Common Mistakes:

• Using incorrect assignment operators
• Missing time format T#5s
• Adding semicolons inside declarations

3. Given the following PLC code snippet for a star-delta starter:

IF Start THEN
  TimerStar(IN:=TRUE, PT:=T#10s);
  IF TimerStar.Q THEN
    TimerDelta(IN:=TRUE, PT:=T#5s);
  END_IF
END_IF

What is the output state of TimerDelta.Q after 12 seconds of Start being TRUE?

medium

A. TRUE

B. TimerDelta.Q resets to FALSE

C. Undefined

D. FALSE

Solution

1. Step 1: Analyze TimerStar behavior

   TimerStar starts when Start is TRUE and runs for 10 seconds. After 10 seconds, TimerStar.Q becomes TRUE.

2. Step 2: Analyze TimerDelta behavior after TimerStar.Q

   Once TimerStar.Q is TRUE (after 10s), TimerDelta starts and runs for 5 seconds. At 12 seconds, TimerDelta has been running for 2 seconds, so TimerDelta.Q is still FALSE. But the code only sets TimerDelta.IN to TRUE when TimerStar.Q is TRUE, so TimerDelta is active.

3. Step 3: Re-examine timing

   At 12 seconds, TimerDelta has been running for 2 seconds (less than 5s), so TimerDelta.Q is FALSE.

4. Final Answer:

   FALSE -> Option D

5. Quick Check:

   TimerDelta.Q after 2s < 5s = FALSE [OK]

Hint: Timer output Q is TRUE only after preset time PT [OK]

Common Mistakes:

• Assuming TimerDelta.Q is TRUE immediately
• Ignoring timer preset times
• Confusing timer input IN with output Q

4. Identify the error in this star-delta timer PLC code snippet:

IF Start THEN
  TimerStar(IN:=Start, PT:=T#10s);
  IF TimerStar.Q THEN
    TimerDelta(IN:=Start, PT:=T#5s);
  END_IF
END_IF

What is the main problem?

medium

A. TimerDelta never starts because IN is tied to Start, not TimerStar.Q

B. TimerStar timer preset time is too short

C. Start input is not used correctly

D. Timers are missing reset logic

Solution

1. Step 1: Check TimerStar input

   TimerStar.IN is correctly tied to Start, so it runs when Start is TRUE.

2. Step 2: Check TimerDelta input

   TimerDelta.IN is tied to Start, not TimerStar.Q. This means TimerDelta starts immediately with Start, not after TimerStar.Q becomes TRUE.

3. Step 3: Identify the problem

   TimerDelta should start only after TimerStar.Q is TRUE to ensure star mode completes before delta starts. Current code starts TimerDelta too early.

4. Final Answer:

   TimerDelta never starts because IN is tied to Start, not TimerStar.Q -> Option A

5. Quick Check:

   TimerDelta.IN must depend on TimerStar.Q [OK]

Hint: TimerDelta.IN should depend on TimerStar.Q, not Start [OK]

Common Mistakes:

• Linking TimerDelta.IN directly to Start
• Ignoring timer sequence dependencies
• Not resetting timers properly

5. You want to design a star-delta starter PLC program where the motor starts in star mode for 8 seconds, then switches to delta mode for 10 seconds, and finally stops. Which timer logic sequence correctly achieves this?

hard

A. Start triggers both TimerStar and TimerDelta simultaneously, motor stops after 18s

B. Start triggers TimerDelta (10s), when TimerDelta.Q is TRUE start TimerStar (8s), then stop motor

C. Start triggers TimerStar (8s), when TimerStar.Q is TRUE start TimerDelta (10s), when TimerDelta.Q is TRUE stop motor

D. Start triggers TimerStar (8s), motor stops immediately after TimerStar.Q is TRUE

Solution

1. Step 1: Understand star-delta timing sequence

   The motor must start in star mode for 8 seconds, then switch to delta mode for 10 seconds, then stop.

2. Step 2: Analyze options

   Start triggers TimerStar (8s), when TimerStar.Q is TRUE start TimerDelta (10s), when TimerDelta.Q is TRUE stop motor correctly sequences timers: TimerStar runs first, then TimerDelta starts after TimerStar.Q is TRUE, then motor stops after TimerDelta.Q is TRUE.

3. Step 3: Eliminate incorrect options

   Start triggers TimerDelta (10s), when TimerDelta.Q is TRUE start TimerStar (8s), then stop motor reverses sequence, Start triggers both TimerStar and TimerDelta simultaneously, motor stops after 18s runs timers simultaneously (wrong), Start triggers TimerStar (8s), motor stops immediately after TimerStar.Q is TRUE stops motor too early.

4. Final Answer:

   Start triggers TimerStar (8s), when TimerStar.Q is TRUE start TimerDelta (10s), when TimerDelta.Q is TRUE stop motor -> Option C

5. Quick Check:

   Sequential timers for star then delta = C [OK]

Hint: Chain timers: star first, then delta, then stop [OK]

Common Mistakes:

• Starting timers simultaneously
• Reversing star and delta order
• Stopping motor too early