Count-up counter (CTU) behavior in PLC Programming - Interactive Code Practice

Practice - 5 Tasks

1fill in blank

easy

Complete the code to initialize the counter value to zero.

PLC Programming

CTU_Counter.PV := [1];

Drag options to blanks, or click blank then click option'

A0

B1

C-1

D10

Attempts:

3 left

💡 Hint

Common Mistakes

Setting the initial value to 1 or a negative number causes incorrect counting.

The preset value (PV) of a count-up counter should start at 0 to count upwards correctly.

2fill in blank

medium

Complete the code to increment the counter when the input is true.

PLC Programming

IF InputSignal THEN CTU_Counter.CU := [1]; END_IF

Drag options to blanks, or click blank then click option'

AFALSE

B1

C0

DTRUE

Attempts:

3 left

💡 Hint

Common Mistakes

Using numeric values instead of boolean TRUE or FALSE.

The count-up input (CU) must be set to TRUE to increment the counter.

3fill in blank

hard

Fix the error in resetting the counter value.

PLC Programming

IF ResetSignal THEN CTU_Counter.CV := [1]; END_IF

Drag options to blanks, or click blank then click option'

ACTU_Counter.CV

B0

CCTU_Counter.PV

D1

Attempts:

3 left

💡 Hint

Common Mistakes

Resetting to the preset value or current value does not clear the counter.

The current value (CV) must be reset to zero to clear the counter.

4fill in blank

hard

Fill both blanks to check if the counter has reached its preset value.

PLC Programming

IF CTU_Counter.CV [1] CTU_Counter.PV THEN CTU_Counter.Q := [2]; END_IF

Drag options to blanks, or click blank then click option'

A>=

B<

CTRUE

DFALSE

Attempts:

3 left

💡 Hint

Common Mistakes

Using '<' instead of '>=' causes wrong output.

Setting Q to FALSE when the count is reached.

The counter output (Q) becomes TRUE when current value (CV) is greater than or equal to preset value (PV).

5fill in blank

hard

Fill all three blanks to create a dictionary of counts for items with counts above zero.

PLC Programming

CountsAboveZero := { [1]: [2] for [3] in Items if Items[[3]] > 0 }

Drag options to blanks, or click blank then click option'

Aitem

BItems[item]

Dcount

Attempts:

3 left

💡 Hint

Common Mistakes

Using different variable names inconsistently.

Not accessing the dictionary value correctly.

We use 'item' as key, 'Items[item]' as value, and iterate over 'item' in Items to filter counts > 0.

Practice

1. What does the done bit in a CTU (Count-Up Counter) indicate?

easy

A. The counter has reached its preset value

B. The counter is reset to zero

C. The counter is currently counting down

D. The counter input is inactive

Solution

1. Step 1: Understand the done bit role

   The done bit is a signal that shows when the counter has reached its preset value.

2. Step 2: Relate done bit to counting

   When the count equals the preset, the done bit turns ON to indicate completion.

3. Final Answer:

   The counter has reached its preset value -> Option A

4. Quick Check:

   Done bit = preset reached [OK]

Hint: Done bit means count reached preset value [OK]

Common Mistakes:

• Confusing done bit with reset signal
• Thinking done bit means counting down
• Assuming done bit is always ON

2. Which of the following is the correct syntax to declare a CTU counter named C1 with a preset of 10 in a typical PLC program?

easy

A. CTU C1 PRE 10

B. CTU(C1, 10);

C. CTU C1, PRE:=10;

D. Counter CTU C1 = 10;

Solution

1. Step 1: Identify correct CTU declaration syntax

   Typical PLC syntax uses the format: CTU counterName, PRE:=presetValue;

2. Step 2: Match options to syntax

   CTU C1, PRE:=10; matches the correct syntax with CTU C1, PRE:=10;

3. Final Answer:

   CTU C1, PRE:=10; -> Option C

4. Quick Check:

   CTU declaration uses PRE:= preset [OK]

Hint: Look for PRE:= syntax in CTU declaration [OK]

Common Mistakes:

• Using parentheses incorrectly
• Missing PRE:= keyword
• Using assignment '=' instead of ':='

3. Given a CTU counter with preset 5 and current count 3, what will be the count and done bit after two rising input pulses?

medium

A. Count = 3, Done bit = TRUE

B. Count = 4, Done bit = FALSE

C. Count = 5, Done bit = FALSE

D. Count = 5, Done bit = TRUE

Solution

1. Step 1: Add two pulses to current count

   Starting at 3, two pulses increase count to 5 (3 + 2 = 5).

2. Step 2: Check if count reached preset

   Count equals preset (5), so done bit becomes TRUE.

3. Final Answer:

   Count = 5, Done bit = TRUE -> Option D

4. Quick Check:

   Count + pulses = preset -> done bit TRUE [OK]

Hint: Add pulses to count, compare with preset [OK]

Common Mistakes:

• Not updating count correctly
• Confusing done bit state
• Assuming done bit is TRUE before preset reached

4. A CTU counter is not setting the done bit even after the count reaches the preset. Which of the following is the most likely cause?

medium

A. The preset value is set higher than intended

B. The done bit is wired incorrectly in the program

C. The counter is counting down instead of up

D. The counter is not receiving rising edge pulses

Solution

1. Step 1: Analyze why done bit is not set

   If count reaches preset but done bit stays off, wiring or logic for done bit is likely wrong.

2. Step 2: Evaluate other options

   If pulses were missing or counting down, count wouldn't reach preset. Preset too high means count can't reach it.

3. Final Answer:

   The done bit is wired incorrectly in the program -> Option B

4. Quick Check:

   Done bit wiring error causes no done signal [OK]

Hint: Check done bit wiring if count reaches preset but no done [OK]

Common Mistakes:

• Assuming pulses are missing without checking
• Ignoring done bit wiring
• Confusing counting direction with done bit issue

5. You have a CTU counter with preset 10. The input pulses come irregularly, sometimes multiple pulses at once. How should you modify the program to ensure the count never exceeds the preset and done bit is set correctly?

hard

A. Ignore extra pulses; CTU automatically limits count to preset

B. Use a separate timer to count pulses instead of CTU

C. Add logic to reset the counter when count exceeds preset

D. Increase the preset value to a higher number

Solution

1. Step 1: Understand CTU behavior with irregular pulses

   CTU increments by 1 per rising edge and automatically limits the accumulator to the preset value, preventing overflow.

2. Step 2: Verify done bit sets correctly

   No modification needed; done bit activates when accumulator reaches preset, even with irregular pulses.

3. Final Answer:

   Ignore extra pulses; CTU automatically limits count to preset -> Option A

4. Quick Check:

   CTU ACC ≤ PRE automatically, done sets [OK]

Hint: CTU automatically limits count to preset [OK]

Common Mistakes:

• Assuming CTU allows count to exceed preset
• Adding unnecessary reset logic for overflow
• Using timer or increasing preset unnecessarily