G81 simple drilling cycle in CNC Programming - Interactive Code Practice

Practice - 5 Tasks

1fill in blank

easy

Complete the code to start a simple drilling cycle with G81.

CNC Programming

G81 X10 Y20 Z-5 R[1] F100

Drag options to blanks, or click blank then click option'

A5

B2

C0

D10

Attempts:

3 left

💡 Hint

Common Mistakes

Using R=0 causes the tool to retract to the surface, risking collision.

Using too large R wastes time.

The R value sets the retract plane height above the part surface. 5 is a common safe retract height.

2fill in blank

medium

Complete the code to specify the feed rate for the drilling cycle.

CNC Programming

G81 X15 Y25 Z-8 R5 F[1]

Drag options to blanks, or click blank then click option'

A10

B100

C200

D50

Attempts:

3 left

💡 Hint

Common Mistakes

Using too low feed rate causes slow drilling.

Using too high feed rate may damage the tool.

F100 sets the feed rate to 100 units per minute, a typical drilling speed.

3fill in blank

hard

Fix the error in the drilling cycle code by completing the blank.

CNC Programming

G81 X20 Y30 Z[1] R5 F100

Drag options to blanks, or click blank then click option'

A10

B0

C-5

D-10

Attempts:

3 left

💡 Hint

Common Mistakes

Using positive Z drills above the surface, no hole is made.

Using zero Z means no drilling depth.

Z must be negative to drill down into the material. -10 means drill 10 units deep.

4fill in blank

hard

Fill both blanks to complete the drilling cycle and cancel it properly.

CNC Programming

G81 X25 Y35 Z[1] R5 F100
G[2]

Drag options to blanks, or click blank then click option'

A-7

B80

Attempts:

3 left

💡 Hint

Common Mistakes

Forgetting to cancel the drilling cycle with G80.

Using positive Z depth.

Z-7 drills 7 units deep. G80 cancels the drilling cycle.

5fill in blank

hard

Fill all three blanks to create a drilling cycle with correct coordinates, depth, and feed rate.

CNC Programming

G81 X[1] Y[2] Z[3] R5 F150

Drag options to blanks, or click blank then click option'

A30

B40

C-12

D20

Attempts:

3 left

💡 Hint

Common Mistakes

Using positive Z depth.

Mixing up X and Y coordinates.

X30 Y40 are coordinates, Z-12 drills 12 units deep.

Practice

1. What is the main purpose of the G81 command in CNC programming?

easy

A. To perform a simple drilling cycle at specified XY positions with a set depth

B. To move the tool rapidly without cutting

C. To set the spindle speed

D. To cancel all active cycles

Solution

1. Step 1: Understand the function of G81

   The G81 command is used to automate drilling holes at multiple XY positions with the same depth.

2. Step 2: Compare with other options

   The other options describe other commands or actions unrelated to drilling cycles.

3. Final Answer:

   To perform a simple drilling cycle at specified XY positions with a set depth -> Option A

4. Quick Check:

   G81 = Simple drilling cycle [OK]

Hint: G81 always means drilling holes at set depth [OK]

Common Mistakes:

• Confusing G81 with rapid move commands
• Thinking G81 sets spindle speed
• Forgetting G81 automates repeated drilling

2. Which of the following is the correct syntax to start a G81 drilling cycle at X10 Y20 with a depth of Z-5 and retract height R2?

easy

A. G81 R2 Z-5 X10 Y20

B. G81 Z-5 X10 Y20 R2

C. G81 X10 Y20 R2 Z-5

D. G81 X10 Y20 Z-5 R2

Solution

1. Step 1: Identify the correct order of parameters in G81

   The standard order is G81 followed by X, Y, then Z for depth, and R for retract height.

2. Step 2: Check each option

   G81 X10 Y20 Z-5 R2 follows the correct order: G81 X10 Y20 Z-5 R2. Others mix the order incorrectly.

3. Final Answer:

   G81 X10 Y20 Z-5 R2 -> Option D

4. Quick Check:

   Correct parameter order = G81 X10 Y20 Z-5 R2 [OK]

Hint: Use G81 X Y Z R in that order for drilling [OK]

Common Mistakes:

• Placing Z before X and Y
• Mixing R and Z order
• Omitting required parameters

3. Given the following CNC program snippet, what is the final Z position of the tool after executing the drilling cycle?

G90 G00 X0 Y0 Z5
G81 X10 Y10 Z-4 R1 F100
G80
G00 Z5

medium

A. Z-4

B. Z1

C. Z5

D. Z0

Solution

1. Step 1: Analyze the drilling cycle commands

   The G81 command drills to Z-4 from retract height R1. After drilling, G80 cancels the cycle.

2. Step 2: Check the final move command

   After G80, the program moves the tool to Z5 with G00, which is a rapid move to safe height.

3. Final Answer:

   Z5 -> Option C

4. Quick Check:

   Final Z after G00 Z5 = Z5 [OK]

Hint: Look for last Z move after G80 to find final position [OK]

Common Mistakes:

• Assuming tool stays at drilling depth
• Ignoring G80 cancels drilling cycle
• Missing final rapid move to safe height

4. Identify the error in this G81 drilling cycle command:

G81 X20 Y30 Z5 R2 F80

medium

A. Z value should be negative for drilling depth

B. R value cannot be used with G81

C. F value is missing

D. X and Y coordinates are not allowed

Solution

1. Step 1: Understand the meaning of Z in drilling

   Z specifies the drilling depth and must be negative to move down into the material.

2. Step 2: Check the given command

   Z5 is positive, which means moving above the surface, not drilling down.

3. Final Answer:

   Z value should be negative for drilling depth -> Option A

4. Quick Check:

   Drilling depth Z must be negative [OK]

Hint: Drilling depth Z is always negative below surface [OK]

Common Mistakes:

• Using positive Z for drilling depth
• Confusing R with retract height
• Ignoring feed rate F

5. You want to drill three holes at positions X10 Y10, X20 Y10, and X30 Y10 with a depth of 6 mm below the surface, retract height 2 mm, and feed rate 120 mm/min. Which of the following programs correctly uses G81 to do this efficiently?

hard

A. G81 X10 Y10 Z-6 R2 F120
G81 X20 Y10 Z-6 R2 F120
G81 X30 Y10 Z-6 R2 F120
G80

B. G81 Z-6 R2 F120
X10 Y10
X20 Y10
X30 Y10
G80

C. G81 X10 Y10 Z6 R2 F120
X20 Y10
X30 Y10
G80

D. G81 Z-6 R2 F120 X10 Y10 X20 Y10 X30 Y10
G80

Solution

1. Step 1: Understand how to use G81 for multiple holes

   Start G81 with drilling parameters, then list XY positions on separate lines to drill multiple holes efficiently.

2. Step 2: Evaluate each option

   G81 Z-6 R2 F120 X10 Y10 X20 Y10 X30 Y10 G80 correctly sets G81 once with parameters, then drills at three XY points, then cancels with G80. G81 X10 Y10 Z-6 R2 F120 G81 X20 Y10 Z-6 R2 F120 G81 X30 Y10 Z-6 R2 F120 G80 repeats G81 unnecessarily. G81 X10 Y10 Z6 R2 F120 X20 Y10 X30 Y10 G80 uses positive Z depth (wrong). G81 Z-6 R2 F120 X10 Y10 X20 Y10 X30 Y10 G80 tries to list all XY in one line, which is invalid.

3. Final Answer:

   G81 Z-6 R2 F120 X10 Y10 X20 Y10 X30 Y10 G80 -> Option B

4. Quick Check:

   One G81 + multiple XY lines = G81 Z-6 R2 F120 X10 Y10 X20 Y10 X30 Y10 G80 [OK]

Hint: Use one G81 with parameters, then list XY positions, end with G80 [OK]

Common Mistakes:

• Repeating G81 for each hole
• Using positive Z for depth
• Trying to put all XY in one line