FILLET and CHAMFER commands in AutoCAD - Cheat Sheet & Quick Revision

Recall & Review

beginner

What does the FILLET command do in AutoCAD?

The FILLET command rounds or creates a smooth arc between two lines or edges, connecting them with a curved corner.

beginner

What is the main difference between FILLET and CHAMFER commands?

FILLET creates a rounded corner (arc), while CHAMFER creates a straight, angled corner (beveled edge) between two lines.

intermediate

How do you specify the radius in the FILLET command?

You enter the radius value before selecting the two lines to fillet. This radius controls the size of the rounded corner.

intermediate

What parameters do you set when using the CHAMFER command?

You set two distances that define how far the chamfer cuts along each line from the corner, creating a straight angled edge.

intermediate

Can FILLET and CHAMFER commands be used on polylines in AutoCAD?

Yes, both commands can be applied to polylines to round or bevel their corners, making shapes smoother or angled.

What shape does the FILLET command create between two lines?

A A circle

B A straight angled line

C A rounded arc

D A square corner

FILLET creates a rounded arc connecting two lines.

Which command creates a beveled edge between two lines?

A CHAMFER

B FILLET

C OFFSET

D TRIM

CHAMFER creates a straight angled (beveled) edge between two lines.

Before selecting lines, what must you specify for the FILLET command?

A Chamfer distances

B Layer color

C Line thickness

D Radius

You specify the radius to control the size of the rounded corner.

How many distances do you set for the CHAMFER command?

A One

B Two

C Three

D None

You set two distances defining how far the chamfer cuts along each line.

Can FILLET and CHAMFER be applied to polylines?

A Yes, both can be applied

B Only FILLET can be applied

C Only CHAMFER can be applied

D Neither can be applied

Both FILLET and CHAMFER commands can be used on polylines.

Explain how the FILLET command works and when you would use it.

Think about smoothing sharp corners.

Describe the steps and parameters needed to create a chamfer between two lines.

Focus on the distances that define the chamfer size.

Practice

1. What does the FILLET command do in AutoCAD?

easy

A. It deletes the corner between two lines.

B. It cuts the corner between two lines by creating a straight edge.

C. It rounds the corner between two lines by creating an arc.

D. It extends lines to meet at a corner.

Solution

1. Step 1: Understand FILLET command purpose

   The FILLET command creates a rounded corner by adding an arc between two intersecting lines.

2. Step 2: Compare with other options

   Only 'It rounds the corner between two lines by creating an arc.' describes rounding with an arc; others describe cutting, deleting, or extending.

3. Final Answer:

   It rounds the corner between two lines by creating an arc. -> Option C

4. Quick Check:

   FILLET = round corner with arc [OK]

Hint: FILLET = round corners with arcs [OK]

Common Mistakes:

• Confusing FILLET with CHAMFER
• Thinking FILLET cuts corners
• Assuming FILLET deletes lines

2. Which of the following is the correct syntax to start the CHAMFER command in AutoCAD?

easy

A. CHAMFERLINE

B. FILLET

C. CHAMF

D. CHAMFER

Solution

1. Step 1: Recall command names in AutoCAD

   The full command to create a chamfer is CHAMFER.

2. Step 2: Check other options

   FILLET creates rounded corners, CHAMF is incomplete, CHAMFERLINE is not valid.

3. Final Answer:

   CHAMFER -> Option D

4. Quick Check:

   Start CHAMFER with "CHAMFER" [OK]

Hint: Type full command name 'CHAMFER' to start [OK]

Common Mistakes:

• Using FILLET instead of CHAMFER
• Typing incomplete command like CHAMF
• Adding extra words to command

3. Given two lines meeting at a corner, what will be the result of applying FILLET with radius 5?

medium

A. A straight angled edge will replace the corner, cutting it off.

B. A rounded corner with an arc of radius 5 will replace the sharp corner.

C. The lines will be extended to meet at a new point 5 units away.

D. The corner will be deleted leaving a gap.

Solution

1. Step 1: Understand FILLET with radius

   FILLET with radius 5 creates an arc of radius 5 rounding the corner.

2. Step 2: Compare with other options

   'A straight angled edge will replace the corner, cutting it off.' describes CHAMFER; the remaining options are incorrect behaviors.

3. Final Answer:

   A rounded corner with an arc of radius 5 will replace the sharp corner. -> Option B

4. Quick Check:

   FILLET radius 5 = rounded arc radius 5 [OK]

Hint: FILLET radius sets arc size for rounding [OK]

Common Mistakes:

• Confusing FILLET radius with CHAMFER distance
• Expecting straight edges instead of arcs
• Thinking lines extend instead of rounding

4. You tried to use the CHAMFER command but got an error. Which of these is the most likely cause?

medium

A. You selected only one line instead of two.

B. You entered a negative distance for the chamfer length.

C. You used FILLET instead of CHAMFER.

D. You set the radius instead of distance.

Solution

1. Step 1: Understand CHAMFER selection requirements

   CHAMFER requires selecting two lines to create the angled edge.

2. Step 2: Analyze error causes

   Selecting only one line causes an error; negative distance or radius settings usually prompt warnings but not immediate errors.

3. Final Answer:

   You selected only one line instead of two. -> Option A

4. Quick Check:

   CHAMFER needs two lines selected [OK]

Hint: Select two lines for CHAMFER to work [OK]

Common Mistakes:

• Selecting only one line
• Confusing FILLET and CHAMFER commands
• Using negative distances

5. You want to create a smooth transition between two lines but also want a flat edge instead of a curve. Which command and settings should you use?

hard

A. Use CHAMFER with equal distances to cut a flat angled edge.

B. Use CHAMFER with radius instead of distance.

C. Use FILLET with a large radius to create a wide curve.

D. Use FILLET with radius 0 to create a sharp corner.

Solution

1. Step 1: Identify desired corner type

   A flat edge means a straight angled cut, which is done by CHAMFER.

2. Step 2: Choose correct CHAMFER settings

   Using equal distances for CHAMFER creates a symmetric flat edge between lines.

3. Step 3: Eliminate incorrect options

   FILLET creates curves, radius 0 is a sharp corner not flat edge, CHAMFER uses distances not radius.

4. Final Answer:

   Use CHAMFER with equal distances to cut a flat angled edge. -> Option A

5. Quick Check:

   Flat edge = CHAMFER with equal distances [OK]

Hint: Flat edges need CHAMFER with equal distances [OK]

Common Mistakes:

• Using FILLET expecting flat edges
• Setting CHAMFER radius instead of distance
• Confusing sharp corner with flat edge