analogRead() and ADC conversion in Arduino - Interactive Code Practice

Practice - 5 Tasks

1fill in blank

easy

Complete the code to read an analog value from pin A0.

Arduino

int sensorValue = analogRead([1]);

Drag options to blanks, or click blank then click option'

AA0

B13

CLED_BUILTIN

DD0

Attempts:

3 left

💡 Hint

Common Mistakes

Using a digital pin number instead of an analog pin.

Confusing analog pins with digital pins.

The analogRead() function reads the voltage on an analog pin. Pin A0 is the first analog input pin on Arduino boards.

2fill in blank

medium

Complete the code to convert the analog reading to a voltage (0-5V).

Arduino

float voltage = sensorValue * ([1] / 1023.0);

Drag options to blanks, or click blank then click option'

A3.3

B5.0

C10.0

D12.0

Attempts:

3 left

💡 Hint

Common Mistakes

Using 3.3V instead of 5.0V for boards with 5V reference.

Dividing by 1024 instead of 1023.

The Arduino ADC converts 0-5V into values from 0 to 1023. To get the voltage, multiply the reading by 5.0/1023.

3fill in blank

hard

Fix the error in the code to correctly read analog input and print voltage.

Arduino

int sensorValue = analogRead(A1);
float voltage = sensorValue * ([1] / 1023.0);
Serial.println(voltage);

Drag options to blanks, or click blank then click option'

A1023

B3.3

C1024

D5.0

Attempts:

3 left

💡 Hint

Common Mistakes

Using 1024 instead of 1023 in the denominator.

Using the wrong reference voltage.

The voltage calculation must use the correct reference voltage, which is 5.0 volts for most Arduino boards.

4fill in blank

hard

Fill both blanks to create a dictionary of analog pin readings greater than 500.

Arduino

int readings[] = {A0, A1, A2};
for (int i = 0; i < 3; i++) {
  int val = analogRead(readings[[1]]);
  if (val [2] 500) {
    Serial.println(val);
  }
}

Drag options to blanks, or click blank then click option'

Ai

B0

C>

D<

Attempts:

3 left

💡 Hint

Common Mistakes

Using a fixed index instead of the loop variable.

Using '<' instead of '>' in the condition.

Use i to index the array and check if the value is greater than 500.

5fill in blank

hard

Fill all three blanks to map analog readings to voltage and print only if voltage is above 2.5V.

Arduino

int sensor = A3;
int reading = analogRead([1]);
float voltage = reading * ([2] / 1023.0);
if (voltage [3] 2.5) {
  Serial.println(voltage);
}

Drag options to blanks, or click blank then click option'

Asensor

B5.0

C>

Dreading

Attempts:

3 left

💡 Hint

Common Mistakes

Using the wrong variable for analogRead.

Using '<' instead of '>' in the if condition.

Read from sensor, convert using 5.0V reference, and print if voltage is greater than 2.5V.

Practice

1. What does the analogRead() function do on an Arduino?

easy

A. It writes a voltage level to an analog pin.

B. It sends a digital signal to an output pin.

C. It resets the Arduino board.

D. It reads an analog voltage and converts it to a number between 0 and 1023.

Solution

1. Step 1: Understand the purpose of analogRead()

   The function analogRead() reads the voltage on an analog pin and converts it to a number.

2. Step 2: Know the range of values returned

   The returned value ranges from 0 (0 volts) to 1023 (maximum reference voltage, usually 5V or 3.3V).

3. Final Answer:

   It reads an analog voltage and converts it to a number between 0 and 1023. -> Option D

4. Quick Check:

   analogRead() returns 0-1023 [OK]

Hint: Remember: analogRead() maps voltage to 0-1023 [OK]

Common Mistakes:

• Thinking analogRead() writes voltage
• Confusing analogRead() with digitalWrite()
• Assuming analogRead() returns voltage directly
• Believing analogRead() resets the board

2. Which of the following is the correct syntax to read an analog value from pin A0?

easy

A. int sensorValue = analogRead(A0);

B. int sensorValue = digitalRead(A0);

C. analogRead(int A0);

D. int sensorValue = analogWrite(A0);

Solution

1. Step 1: Identify the correct function for analog input

   The function to read analog input is analogRead(), not digitalRead() or analogWrite().

2. Step 2: Check the syntax for reading from pin A0

   The correct syntax is int sensorValue = analogRead(A0); which stores the read value in an integer variable.

3. Final Answer:

   int sensorValue = analogRead(A0); -> Option A

4. Quick Check:

   Use analogRead(pin) to read analog input [OK]

Hint: Use analogRead(pin) to get analog input value [OK]

Common Mistakes:

• Using digitalRead() for analog pins
• Calling analogRead() with wrong syntax
• Using analogWrite() instead of analogRead()
• Trying to pass pin as int inside analogRead()

3. What will be the output of this Arduino code snippet if the analog voltage on pin A1 is 2.5V and the reference voltage is 5V?

int sensorValue = analogRead(A1);
Serial.println(sensorValue);

medium

A. 1023

B. 512

C. 256

D. 0

Solution

1. Step 1: Understand the ADC conversion formula

   The analogRead() converts voltage to a value between 0 and 1023 based on the formula: value = (input voltage / reference voltage) * 1023.

2. Step 2: Calculate the expected value for 2.5V input

   value = (2.5 / 5) * 1023 = 0.5 * 1023 = 511.5, which rounds to 512.

3. Final Answer:

   512 -> Option B

4. Quick Check:

   Half of 1023 is about 512 [OK]

Hint: Multiply voltage ratio by 1023 for analogRead() value [OK]

Common Mistakes:

• Using 1023 directly without scaling
• Confusing digitalRead() output with analogRead()
• Rounding errors ignoring half values
• Assuming analogRead() returns voltage in volts

4. Identify the error in this Arduino code that reads an analog value and prints it:

void setup() {
  Serial.begin(9600);
}

void loop() {
  int val = analogRead(0);
  Serial.print(val);
  delay(1000);
}

medium

A. Serial.begin() must be called inside loop(), not setup().

B. delay() cannot be used with Serial.print().

C. analogRead() should use A0 instead of 0 for clarity and correctness.

D. The variable val must be declared as float, not int.

Solution

1. Step 1: Check the analogRead() argument

   Using 0 instead of A0 can work but is discouraged; A0 is the correct constant for analog pin 0.

2. Step 2: Verify other code parts

   Serial.begin() is correctly in setup(), delay() works fine with Serial.print(), and int is suitable for analogRead() values.

3. Final Answer:

   analogRead() should use A0 instead of 0 for clarity and correctness. -> Option C

4. Quick Check:

   Use A0 for analog pin 0 [OK]

Hint: Use A0 constant for analog pin 0 [OK]

Common Mistakes:

• Using numeric 0 instead of A0 for analogRead()
• Moving Serial.begin() to loop() causing repeated starts
• Thinking delay() stops Serial.print()
• Declaring analogRead() result as float unnecessarily

5. You want to measure a sensor voltage that ranges from 0V to 3.3V using Arduino's analogRead() with a 5V reference. How can you correctly convert the analogRead() value to the actual voltage?

hard

A. Voltage = (analogRead() / 1023.0) * 5.0

B. Voltage = (analogRead() / 1023.0) * 3.3

C. Voltage = (analogRead() / 5.0) * 3.3

D. Voltage = analogRead() * 3.3 / 1023

Solution

1. Step 1: Understand the reference voltage and sensor range

   The Arduino ADC uses 5V as reference, so analogRead() maps 0-5V to 0-1023.

2. Step 2: Calculate voltage from analogRead() value

   To get voltage, multiply the fraction (analogRead()/1023) by 5.0 (the reference voltage), not 3.3.

3. Final Answer:

   Voltage = (analogRead() / 1023.0) * 5.0 -> Option A

4. Quick Check:

   Use reference voltage (5V) in conversion formula [OK]

Hint: Multiply analogRead ratio by reference voltage (5V) [OK]

Common Mistakes:

• Using sensor max voltage (3.3V) instead of reference voltage (5V)
• Dividing by 5 instead of 1023
• Multiplying analogRead() directly without division
• Confusing sensor voltage range with ADC reference