Costmap configuration (static, obstacle, inflation) in ROS - Interactive Code Practice

Practice - 5 Tasks

1fill in blank

easy

Complete the code to define the static layer plugin in the costmap configuration.

ROS

plugins:
  - {name: static_layer, type: [1]

Drag options to blanks, or click blank then click option'

Acostmap_2d::ObstacleLayer

Bcostmap_2d::InflationLayer

Ccostmap_2d::StaticLayer

Dcostmap_2d::VoxelLayer

Attempts:

3 left

💡 Hint

Common Mistakes

Using ObstacleLayer instead of StaticLayer for static obstacles.

Confusing InflationLayer as static layer plugin.

The static layer plugin is specified by costmap_2d::StaticLayer in the costmap configuration.

2fill in blank

medium

Complete the code to set the inflation radius parameter.

ROS

inflation:
  inflation_radius: [1]

Drag options to blanks, or click blank then click option'

A5.0

B1.0

C2.0

D0.5

Attempts:

3 left

💡 Hint

Common Mistakes

Setting inflation radius to zero disables inflation.

Using too large a radius can block too much space.

The inflation radius defines how far the costmap inflates obstacles. A common default is 1.0 meter.

3fill in blank

hard

Fix the error in the obstacle layer plugin type.

ROS

plugins:
  - {name: obstacle_layer, type: [1]

Drag options to blanks, or click blank then click option'

Acostmap_2d::ObstacleLayer

Bcostmap_2d::StaticLayer

Ccostmap_2d::InflationLayer

Dcostmap_2d::VoxelLayer

Attempts:

3 left

💡 Hint

Common Mistakes

Using StaticLayer for obstacle detection.

Confusing InflationLayer as obstacle plugin.

The obstacle layer plugin must be costmap_2d::ObstacleLayer to detect dynamic obstacles.

4fill in blank

hard

Fill both blanks to configure the inflation layer's cost scaling factor and inflation radius.

ROS

inflation:
  cost_scaling_factor: [1]
  inflation_radius: [2]

Drag options to blanks, or click blank then click option'

A10.0

B1.0

C0.5

D5.0

Attempts:

3 left

💡 Hint

Common Mistakes

Swapping values between cost scaling factor and inflation radius.

Using zero or negative values.

The cost scaling factor controls how quickly costs drop off, often set to 10.0. The inflation radius defines the inflation distance, here 0.5 meters.

5fill in blank

hard

Fill all three blanks to define plugins for static, obstacle, and inflation layers respectively.

ROS

plugins:
  - {name: static_layer, type: [1]
  - {name: obstacle_layer, type: [2]
  - {name: inflation_layer, type: [3]

Drag options to blanks, or click blank then click option'

Acostmap_2d::StaticLayer

Bcostmap_2d::ObstacleLayer

Ccostmap_2d::InflationLayer

Dcostmap_2d::VoxelLayer

Attempts:

3 left

💡 Hint

Common Mistakes

Mixing plugin types between layers.

Using VoxelLayer which is unrelated here.

The static layer uses StaticLayer, obstacle layer uses ObstacleLayer, and inflation layer uses InflationLayer plugins.

Practice

1. Which costmap layer in ROS is responsible for marking fixed obstacles from a pre-existing map?

easy

A. Obstacle layer

B. Inflation layer

C. Static layer

D. Sensor layer

Solution

1. Step 1: Understand the role of the static layer

   The static layer uses a pre-built map to mark fixed obstacles that do not change over time.

2. Step 2: Compare with other layers

   The obstacle layer updates obstacles dynamically from sensors, and the inflation layer adds safety buffers, so they do not mark fixed obstacles directly.

3. Final Answer:

   Static layer -> Option C

4. Quick Check:

   Fixed obstacles = Static layer [OK]

Hint: Static layer = fixed map obstacles [OK]

Common Mistakes:

• Confusing obstacle layer with static layer
• Thinking inflation layer marks obstacles
• Assuming sensor data is static

2. Which of the following YAML snippets correctly enables the inflation layer in a ROS costmap configuration?

easy

A. inflation:
enable: true
radius: 0.5

B. inflation_layer:
active: yes
radius: 1.0

C. inflation_layer:
enabled: false
inflation_radius: 0.5

D. inflation_layer:
enabled: true
inflation_radius: 0.5

Solution

1. Step 1: Check correct keys for inflation layer

   The correct keys are 'inflation_layer' with 'enabled' and 'inflation_radius' as parameters.

2. Step 2: Validate values and syntax

   inflation_layer: enabled: true inflation_radius: 0.5 uses 'enabled: true' and 'inflation_radius: 0.5', which is correct YAML syntax and valid keys.

3. Final Answer:

   inflation_layer: enabled: true inflation_radius: 0.5 -> Option D

4. Quick Check:

   Correct keys and true enabled = inflation_layer: enabled: true inflation_radius: 0.5 [OK]

Hint: Look for 'enabled: true' and 'inflation_radius' keys [OK]

Common Mistakes:

• Using wrong key names like 'enable' or 'active'
• Setting enabled to false when enabling
• Incorrect indentation or YAML syntax

3. Given this costmap configuration snippet:

obstacle_layer:
  observation_sources: laser_scan_sensor
  laser_scan_sensor:
    data_type: LaserScan
    topic: /scan
    marking: true
    clearing: true
inflation_layer:
  inflation_radius: 0.7
  cost_scaling_factor: 10.0

What effect does setting marking: true and clearing: true have on the obstacle layer?

medium

A. It marks obstacles detected by the laser and clears free space around them

B. It disables obstacle detection and only inflates existing obstacles

C. It marks obstacles but does not clear any free space

D. It clears obstacles but does not mark new ones

Solution

1. Step 1: Understand marking and clearing flags

   Setting 'marking: true' means detected obstacles are added to the costmap. 'clearing: true' means free space detected is cleared from the costmap.

2. Step 2: Apply to laser_scan_sensor

   The laser scan sensor will mark obstacles and clear free space dynamically based on sensor data.

3. Final Answer:

   It marks obstacles detected by the laser and clears free space around them -> Option A

4. Quick Check:

   marking + clearing true = mark and clear obstacles [OK]

Hint: marking=true adds obstacles, clearing=true removes free space [OK]

Common Mistakes:

• Assuming clearing disables marking
• Thinking marking disables clearing
• Confusing cost_scaling_factor with marking

4. You have this partial costmap config:

inflation_layer:
  inflation_radius: 0.6
  cost_scaling_factor: -5.0

What is the problem with this configuration?

medium

A. inflation_radius must be an integer, not a float

B. Negative cost_scaling_factor is invalid and causes inflation errors

C. Missing 'enabled: true' disables inflation layer

D. cost_scaling_factor should be zero to disable inflation

Solution

1. Step 1: Check cost_scaling_factor value

   The cost_scaling_factor controls how quickly costs drop off from obstacles. It must be positive; negative values are invalid.

2. Step 2: Understand impact of negative value

   A negative cost_scaling_factor causes errors or unexpected inflation behavior in the costmap.

3. Final Answer:

   Negative cost_scaling_factor is invalid and causes inflation errors -> Option B

4. Quick Check:

   cost_scaling_factor < 0 = error [OK]

Hint: cost_scaling_factor must be positive [OK]

Common Mistakes:

• Thinking inflation_radius must be integer
• Assuming missing enabled disables inflation
• Believing zero cost_scaling_factor disables inflation

5. You want to configure a ROS costmap that uses a static map, detects obstacles with a laser scanner, and inflates obstacles with a radius of 0.8 meters. Which of the following combined configurations is correct?

hard

A. static_layer:
map_topic: /map
obstacle_layer:
observation_sources: laser_scan
laser_scan:
data_type: LaserScan
topic: /scan
marking: true
clearing: true
inflation_layer:
enabled: true
inflation_radius: 0.8
cost_scaling_factor: 5.0

B. static_layer:
enabled: false
obstacle_layer:
observation_sources: laser
laser:
data_type: PointCloud
topic: /scan
marking: false
clearing: true
inflation_layer:
inflation_radius: 0.8
cost_scaling_factor: -1.0

C. static_layer:
map_topic: /map
obstacle_layer:
observation_sources: laser_scan
laser_scan:
data_type: LaserScan
topic: /scan
marking: false
clearing: false
inflation_layer:
enabled: true
inflation_radius: 1.0
cost_scaling_factor: 10.0

D. static_layer:
map_topic: /map
obstacle_layer:
observation_sources: laser_scan
laser_scan:
data_type: LaserScan
topic: /scan
marking: true
clearing: false
inflation_layer:
enabled: true
inflation_radius: 0.5
cost_scaling_factor: 5.0

Solution

1. Step 1: Verify static layer configuration

   static_layer: map_topic: /map obstacle_layer: observation_sources: laser_scan laser_scan: data_type: LaserScan topic: /scan marking: true clearing: true inflation_layer: enabled: true inflation_radius: 0.8 cost_scaling_factor: 5.0 correctly sets 'static_layer' with 'map_topic: /map' to use the static map.

2. Step 2: Check obstacle layer settings

   static_layer: map_topic: /map obstacle_layer: observation_sources: laser_scan laser_scan: data_type: LaserScan topic: /scan marking: true clearing: true inflation_layer: enabled: true inflation_radius: 0.8 cost_scaling_factor: 5.0 uses 'laser_scan' with correct data_type, topic, and both marking and clearing enabled for proper obstacle detection.

3. Step 3: Confirm inflation layer parameters

   static_layer: map_topic: /map obstacle_layer: observation_sources: laser_scan laser_scan: data_type: LaserScan topic: /scan marking: true clearing: true inflation_layer: enabled: true inflation_radius: 0.8 cost_scaling_factor: 5.0 enables inflation with radius 0.8 and a positive cost_scaling_factor, matching requirements.

4. Final Answer:

   static_layer: map_topic: /map obstacle_layer: observation_sources: laser_scan laser_scan: data_type: LaserScan topic: /scan marking: true clearing: true inflation_layer: enabled: true inflation_radius: 0.8 cost_scaling_factor: 5.0 -> Option A

5. Quick Check:

   All layers correct and enabled = static_layer: map_topic: /map obstacle_layer: observation_sources: laser_scan laser_scan: data_type: LaserScan topic: /scan marking: true clearing: true inflation_layer: enabled: true inflation_radius: 0.8 cost_scaling_factor: 5.0 [OK]

Hint: Check all layers enabled with correct parameters [OK]

Common Mistakes:

• Disabling static layer or obstacle marking
• Using negative cost_scaling_factor
• Setting inflation_radius different from 0.8