Trend charts for process variables in PLC Programming - Cheat Sheet & Quick Revision

Recall & Review

beginner

What is a trend chart in process control?

A trend chart is a graph that shows how a process variable changes over time. It helps operators see patterns and spot problems early.

beginner

Why are trend charts important for process variables?

They help monitor the process continuously, detect abnormal changes, and support decision-making to keep the process stable.

beginner

Name two common process variables shown on trend charts.

Temperature and pressure are common process variables displayed on trend charts.

intermediate

How does a PLC collect data for trend charts?

A PLC reads sensors connected to the process, records the values at set intervals, and sends the data to a display or historian system for charting.

intermediate

What is the role of time intervals in trend charts?

Time intervals determine how often data points are recorded. Short intervals show detailed changes, while longer intervals show overall trends.

What does a trend chart primarily display?

A The control program code

B The list of all process variables

C Changes of a process variable over time

D The maximum value of a variable only

Trend charts show how a process variable changes over time, helping to monitor the process.

Which device typically collects data for trend charts in industrial automation?

A Smartphone

B PLC (Programmable Logic Controller)

C Desktop computer

D Printer

PLCs read sensor data and provide it for trend charts in process control.

Why might you choose a shorter time interval for data recording in a trend chart?

A To see detailed changes quickly

B To reduce data storage

C To ignore small changes

D To slow down the process

Short intervals capture detailed changes in the process variable.

Which of these is NOT a typical process variable shown on trend charts?

A Color of the operator's uniform

B Pressure

C Temperature

D Flow rate

Operator uniform color is unrelated to process variables.

What is the main benefit of using trend charts in process automation?

A Changing sensor hardware

B Writing PLC code faster

C Printing reports automatically

D Detecting abnormal process behavior early

Trend charts help spot problems early by showing variable changes over time.

Explain how trend charts help in monitoring process variables in automation.

Think about how seeing data over time helps operators.

Describe the role of a PLC in creating trend charts for process variables.

Consider how the PLC interacts with sensors and displays.

Practice

1. What is the main purpose of a trend chart in PLC programming for process variables?

easy

A. To show how process variables change over time

B. To control the speed of the PLC processor

C. To reset the PLC memory automatically

D. To display error messages only

Solution

1. Step 1: Understand the role of trend charts

   Trend charts are used to visualize data changes over time, especially for process variables like temperature or pressure.

2. Step 2: Eliminate unrelated options

   Options about controlling processor speed, resetting memory, or showing errors do not relate to trend charts.

3. Final Answer:

   To show how process variables change over time -> Option A

4. Quick Check:

   Trend charts = show variable changes over time [OK]

Hint: Trend charts visualize data changes over time [OK]

Common Mistakes:

• Confusing trend charts with control functions
• Thinking trend charts reset PLC memory
• Assuming trend charts only show errors

2. Which of the following is the correct way to declare an array to store 10 samples of a process variable in a PLC program?

easy

A. ARRAY samples[10] REAL;

B. samples = [10] REAL;

C. VAR samples: REAL[10]; END_VAR

D. VAR samples: ARRAY[1..10] OF REAL; END_VAR

Solution

1. Step 1: Recognize PLC array declaration syntax

   In many PLC languages, arrays are declared with VAR, specifying index range and type, e.g., ARRAY[1..10] OF REAL.

2. Step 2: Check each option

   VAR samples: ARRAY[1..10] OF REAL; END_VAR matches correct syntax. Options A, B, and D use incorrect or invalid syntax for PLC arrays.

3. Final Answer:

   VAR samples: ARRAY[1..10] OF REAL; END_VAR -> Option D

4. Quick Check:

   Correct PLC array syntax = VAR samples: ARRAY[1..10] OF REAL; END_VAR [OK]

Hint: Use VAR and ARRAY with index range for PLC arrays [OK]

Common Mistakes:

• Using incorrect brackets or missing VAR keyword
• Confusing array syntax with other languages
• Not specifying index range properly

3. Given the following PLC code snippet that samples a temperature every cycle and stores it in an array of size 5, what will be the content of the array after 7 cycles?

VAR samples: ARRAY[1..5] OF REAL; index: INT := 1; temp: REAL; END_VAR

// On each cycle:
temp := ReadTemperature();
samples[index] := temp;
index := index + 1;
IF index > 5 THEN
  index := 1;
END_IF

medium

A. The array is empty because index resets too early

B. The array contains the first 5 temperature samples from cycles 1 to 5

C. The array contains the last 5 temperature samples from cycles 3 to 7

D. The array contains only the temperature from cycle 7 repeated

Solution

1. Step 1: Understand the circular buffer logic

   The index increments each cycle and resets to 1 after 5, so the array stores the last 5 samples in a loop.

2. Step 2: Analyze after 7 cycles

   After 7 cycles, index has wrapped around once. The array holds samples from cycles 3 to 7, overwriting the first two samples.

3. Final Answer:

   The array contains the last 5 temperature samples from cycles 3 to 7 -> Option C

4. Quick Check:

   Circular buffer stores last 5 samples = The array contains the last 5 temperature samples from cycles 3 to 7 [OK]

Hint: Index resets after max size to overwrite oldest samples [OK]

Common Mistakes:

• Thinking array holds first 5 samples only
• Assuming array is empty due to index reset
• Believing array repeats last sample only

4. Identify the error in this PLC code snippet intended to sample a pressure value every 10 cycles and store it in an array:

VAR samples: ARRAY[1..5] OF REAL; counter: INT := 0; index: INT := 1; pressure: REAL; END_VAR

counter := counter + 1;
IF counter = 10 THEN
  samples[index] := ReadPressure();
  index := index + 1;
  counter := 0;
  IF index > 5 THEN
    index := 1;
  END_IF
END_IF

medium

A. The counter increments every cycle but sampling happens only when counter equals 10

B. The index reset condition should be inside the first IF block

C. The counter should reset after index increments, not before

D. The index reset condition is outside the sampling IF block, causing incorrect indexing

Solution

1. Step 1: Review index reset placement

   The index reset IF was outside the sampling IF, causing it to run every cycle and reset index prematurely.

2. Step 2: Correct placement

   Moving the index reset condition inside the sampling IF block ensures index resets only after a new sample is stored, preventing incorrect indexing.

3. Final Answer:

   The index reset condition should be inside the first IF block -> Option B

4. Quick Check:

   Index reset must be inside sampling block [OK]

Hint: Keep index reset inside sampling condition to avoid errors [OK]

Common Mistakes:

• Placing index reset outside sampling condition
• Resetting counter at wrong time
• Misunderstanding counter increment logic

5. You want to create a trend chart that samples a flow rate every 5 seconds and stores the last 12 samples. Which approach correctly implements this in a PLC program?

hard

A. Use a timer that triggers every 5 seconds to read flow rate, store it in a 12-element array, and use a circular index to overwrite oldest samples.

B. Sample flow rate every cycle without timing, store in a 12-element array, reset index after 12 cycles.

C. Use a timer to sample every 12 seconds, store in a 5-element array, and reset index after 5 samples.

D. Sample flow rate only once at start, store in a 12-element array, then never update.

Solution

1. Step 1: Match sampling frequency and storage size

   The requirement is to sample every 5 seconds and keep last 12 samples, so timer interval and array size must match.

2. Step 2: Use circular buffer logic

   Using a timer to trigger sampling every 5 seconds and a circular index to overwrite oldest samples in a 12-element array fits the need.

3. Final Answer:

   Use a timer that triggers every 5 seconds to read flow rate, store it in a 12-element array, and use a circular index to overwrite oldest samples. -> Option A

4. Quick Check:

   Timer + circular buffer = correct trend sampling [OK]

Hint: Timer triggers sampling; circular buffer stores last samples [OK]

Common Mistakes:

• Sampling every cycle without timing control
• Using wrong timer interval or array size
• Not overwriting oldest samples properly