G85 boring cycle in CNC Programming

Introduction

The G85 boring cycle helps machines make smooth, precise holes by boring without retracting between cuts.

When you need to enlarge or finish a hole with a smooth surface.

When drilling deep holes that require multiple passes.

When you want to avoid tool wear from rapid retracting and feeding.

When programming CNC lathes or milling machines for hole boring.

When you want consistent hole diameter and depth in one cycle.

Syntax

CNC Programming

G85 X... Z... R... Q... F... ;

X and Z specify the hole position or depth depending on machine setup.

R is the retract plane, Q is the depth of each boring pass, F is feed rate.

Examples

Bores a hole at X=50, Z=-20 depth, retracts 2 units above, with 2 units per boring pass at feed 0.1.

CNC Programming

G85 X50 Z-20 R2 Q2 F0.1 ;

Bores a smaller hole with shallower passes and slower feed.

CNC Programming

G85 X30 Z-15 R1 Q1 F0.05 ;

Sample Program

This program sets up the machine, moves near the hole, performs a G85 boring cycle to depth Z-20 with passes of 2 units, then retracts and ends.

CNC Programming

N10 G90 G54 ; Set absolute positioning and work offset
N20 T0101 ; Select tool 1
N30 M06 ; Tool change
N40 G00 X50 Z5 ; Rapid move near hole
N50 G85 X50 Z-20 R2 Q2 F0.1 ; Boring cycle
N60 G00 Z100 ; Retract
N70 M30 ; End program

Important Notes

G85 is a boring cycle that feeds in and retracts in one smooth motion without dwell.

Make sure to set the correct retract plane (R) to avoid collisions.

Feed rate (F) controls how fast the boring tool moves during cutting.

Summary

G85 is used for smooth boring cycles without dwell.

It uses parameters for position, retract height, pass depth, and feed rate.

It helps create precise holes with consistent diameter and finish.

Practice

1. What is the primary purpose of the G85 command in CNC programming?

easy

A. To perform rapid positioning without cutting

B. To drill a hole with peck drilling cycles

C. To perform a boring cycle without dwell for smooth hole finishing

D. To execute a tapping cycle for threads

Solution

1. Step 1: Understand the function of G85 and compare with other cycles

   G85 is a boring cycle used to create holes smoothly without dwell time, unlike other cycles that may pause. Drilling uses G81 or peck drilling uses G83; tapping uses G84. G85 is specifically for boring without dwell.

2. Final Answer:

   To perform a boring cycle without dwell for smooth hole finishing -> Option C

3. Quick Check:

   G85 = boring cycle without dwell [OK]

Hint: G85 = boring without pause, not drilling or tapping [OK]

Common Mistakes:

• Confusing G85 with drilling cycles like G81 or G83
• Thinking G85 includes dwell time
• Mixing G85 with tapping cycles

2. Which of the following is the correct syntax for a G85 boring cycle command?

easy

A. G85 X20.0 Y10.0 Z-15.0 R5.0 F100

B. G85 X20.0 Y10.0 Z-15.0 R5.0 S100

C. G85 X20.0 Y10.0 Z-15.0 F100 D5.0

D. G85 X20.0 Y10.0 Z-15.0 R5.0 T100

Solution

1. Step 1: Identify required parameters in G85 and check each option

   G85 requires X, Y, Z for position, R for retract height, and F for feed rate. G85 X20.0 Y10.0 Z-15.0 R5.0 F100 uses X, Y, Z, R, and F correctly. Others use incorrect parameters like S, D, or T which are not valid here.

2. Final Answer:

   G85 X20.0 Y10.0 Z-15.0 R5.0 F100 -> Option A

3. Quick Check:

   Correct G85 syntax includes R and F [OK]

Hint: Look for R (retract) and F (feed) parameters in G85 [OK]

Common Mistakes:

• Using S or T instead of F for feed rate
• Omitting retract height R parameter
• Confusing feed rate with spindle speed

3. What will be the tool movement sequence for the command G85 X30 Y20 Z-10 R2 F80?

medium

A. Feed directly to Z-10, dwell, then rapid retract to R2

B. Rapid to retract height 2, feed to Z-10, then rapid retract

C. Rapid to Z-10, dwell, then feed to retract height 2

D. Feed to retract height 2, rapid to Z-10, then feed retract

Solution

1. Step 1: Understand G85 movement sequence and match to options

   G85 moves rapidly to retract height (R2), then feeds down to final depth (Z-10) without dwell, then retracts rapidly. Rapid to retract height 2, feed to Z-10, then rapid retract matches this. Others mention dwell or wrong order.

2. Final Answer:

   Rapid to retract height 2, feed to Z-10, then rapid retract -> Option B

3. Quick Check:

   G85 = rapid to R, feed to Z, rapid retract [OK]

Hint: G85 always rapid to R, feed to Z, then rapid retract [OK]

Common Mistakes:

• Assuming dwell occurs in G85
• Mixing feed and rapid moves order
• Confusing retract height with final depth

4. Identify the error in this G85 command: G85 X25 Y15 Z-12 F120

medium

A. Missing retract height parameter R

B. Incorrect feed rate parameter F

C. Z value should be positive

D. X and Y coordinates cannot be used together

Solution

1. Step 1: Check required parameters for G85 and analyze given command

   G85 requires retract height R to define safe rapid retract position. The command lacks R parameter, which is mandatory. Feed rate F and coordinates are correct; Z can be negative for depth.

2. Final Answer:

   Missing retract height parameter R -> Option A

3. Quick Check:

   G85 needs R parameter [OK]

Hint: Always include R for retract height in G85 [OK]

Common Mistakes:

• Omitting retract height R
• Thinking Z must be positive
• Believing X and Y cannot be combined

5. You want to bore a hole 20 mm deep with a retract height of 3 mm and feed rate of 90 mm/min using G85. Which command correctly achieves this if the hole center is at X50 Y40?

hard

A. G85 X50 Y40 Z-20 F90

B. G85 X50 Y40 Z20 R3 F90

C. G85 X50 Y40 Z-20 R30 F90

D. G85 X50 Y40 Z-20 R3 F90

Solution

1. Step 1: Set correct depth and retract height, then verify feed rate and coordinates

   Depth is negative for downward movement, so Z-20 is correct. Retract height R3 means rapid retract to 3 mm above surface. Feed rate F90 is correct. X50 Y40 sets hole center. G85 X50 Y40 Z-20 R3 F90 has all correct parameters.

2. Final Answer:

   G85 X50 Y40 Z-20 R3 F90 -> Option D

3. Quick Check:

   Negative Z for depth, R for retract, F for feed [OK]

Hint: Depth is negative Z, retract R positive, feed F set [OK]

Common Mistakes:

• Using positive Z for depth
• Setting retract height too large
• Omitting retract height R