Primitive solids (box, cylinder, sphere, cone) in AutoCAD - Interactive Code Practice

Practice - 5 Tasks

1fill in blank

easy

Complete the code to create a box with given length, width, and height.

AutoCAD

[1] 0,0,0 10,20,30

Drag options to blanks, or click blank then click option'

ACREATE

BBOX

CSOLID

DMAKE

Attempts:

3 left

💡 Hint

Common Mistakes

Using 'CREATE' instead of 'BOX' as the command.

Typing 'SOLID' which is not a direct command for box creation.

The command to create a box primitive solid in AutoCAD is BOX.

2fill in blank

medium

Complete the code to create a cylinder with a radius of 5 and height of 15.

AutoCAD

[1] 0,0,0 5 15

Drag options to blanks, or click blank then click option'

ACYLINDER

BCREATE

CMAKE

DSOLID

Attempts:

3 left

💡 Hint

Common Mistakes

Using 'CREATE' or 'MAKE' which are not valid commands here.

Typing 'SOLID' which is not the direct command for cylinder.

The command to create a cylinder primitive solid in AutoCAD is CYLINDER.

3fill in blank

hard

Fix the error in the code to create a sphere with radius 10.

AutoCAD

[1] 0,0,0 10

Drag options to blanks, or click blank then click option'

ASPHERE

BCREATE

CMAKE

DSOLID

Attempts:

3 left

💡 Hint

Common Mistakes

Using 'CREATE' or 'MAKE' which are not valid commands here.

Typing 'SOLID' which is not the direct command for sphere.

The correct command to create a sphere primitive solid is SPHERE.

4fill in blank

hard

Fill both blanks to create a cone with base radius 7 and height 20.

AutoCAD

[1] 0,0,0 [2] 20

Drag options to blanks, or click blank then click option'

A7

BCONE

DMAKE

Attempts:

3 left

💡 Hint

Common Mistakes

Using 'MAKE' instead of 'CONE' for the command.

Confusing the radius and height values.

The command to create a cone is CONE followed by the base center point, base radius, and height. Here, CONE is the correct keyword to start the command and 7 is the base radius.

5fill in blank

hard

Fill all three blanks to create a box with length 10, width 15, and height 20.

AutoCAD

[1] 0,0,0 [2] [3] 20

Drag options to blanks, or click blank then click option'

ABOX

B10

C15

DMAKE

Attempts:

3 left

💡 Hint

Common Mistakes

Using 'MAKE' instead of 'BOX' for the command.

Swapping length and width values.

The command to create a box starts with BOX, followed by the base point, then length and width, and finally height.

Practice

1. Which of the following primitive solids in AutoCAD is shaped like a ball?

easy

A. Box

B. Sphere

C. Cylinder

D. Cone

Solution

1. Step 1: Understand the shape of each primitive solid

   A sphere is a perfectly round 3D shape like a ball, while a box is a cube or rectangular prism, a cylinder is like a can, and a cone is like an ice cream cone.

2. Step 2: Match the shape to the description

   The shape described as a ball matches the sphere.

3. Final Answer:

   Sphere -> Option B

4. Quick Check:

   Ball shape = Sphere [OK]

Hint: Think of a ball shape for sphere [OK]

Common Mistakes:

• Confusing cylinder with sphere
• Thinking box is round
• Mixing cone and sphere shapes

2. Which AutoCAD command correctly creates a cylinder primitive solid?

easy

A. SPHERE

B. BOX

C. CYLINDER

D. CONE

Solution

1. Step 1: Recall the command names for primitive solids

   AutoCAD uses specific commands: BOX for box, CYLINDER for cylinder, SPHERE for sphere, and CONE for cone.

2. Step 2: Identify the command for cylinder

   The command to create a cylinder is CYLINDER.

3. Final Answer:

   CYLINDER -> Option C

4. Quick Check:

   Command for cylinder = CYLINDER [OK]

Hint: Use the exact shape name as command [OK]

Common Mistakes:

• Typing BOX to create cylinder
• Using SPHERE command for cylinder
• Misspelling CYLINDER

3. What will be the result of this AutoCAD command sequence?

BOX
Specify corner of box or [Center]: 0,0,0
Specify other corner: 5,5,0
Specify height: 10

medium

A. A box with base 5x5 units and height 10 units

B. A box with base 10x10 units and height 5 units

C. A flat square with no height

D. An error because height is missing

Solution

1. Step 1: Analyze the BOX command inputs

   The first corner is at (0,0,0), the opposite corner is at (5,5,0), so the base is 5 units by 5 units.

2. Step 2: Check the height input

   The height specified is 10 units, so the box extends 10 units upward.

3. Final Answer:

   A box with base 5x5 units and height 10 units -> Option A

4. Quick Check:

   Base 5x5 and height 10 = A box with base 5x5 units and height 10 units [OK]

Hint: Base corners define length and width; height is separate [OK]

Common Mistakes:

• Mixing base dimensions with height
• Assuming height is zero
• Confusing corner points

4. You typed the command SPHERE but AutoCAD gave an error. Which is the most likely cause?

medium

A. You forgot to start AutoCAD

B. You typed SPHERE in lowercase

C. You tried to create a box instead

D. You did not specify the sphere radius

Solution

1. Step 1: Understand the SPHERE command requirements

   SPHERE command requires you to specify the center point and then the radius to create the sphere.

2. Step 2: Identify common error causes

   If you skip specifying the radius, AutoCAD cannot create the sphere and shows an error.

3. Final Answer:

   You did not specify the sphere radius -> Option D

4. Quick Check:

   Missing radius causes error [OK]

Hint: Always enter radius after center for sphere [OK]

Common Mistakes:

• Ignoring radius input
• Thinking case matters in commands
• Trying wrong commands

5. You want to create a cone with a base radius of 4 units and height of 9 units. Which sequence of commands and inputs is correct?

hard

A. CONE
Specify center of base: 0,0,0
Specify radius of base: 4
Specify height: 9

B. CONE
Specify height: 9
Specify radius of base: 4
Specify center of base: 0,0,0

C. CYLINDER
Specify center of base: 0,0,0
Specify radius of base: 4
Specify height: 9

D. CONE
Specify radius of base: 9
Specify center of base: 0,0,0
Specify height: 4

Solution

1. Step 1: Recall the correct command and input order for cone

   The command is CONE. The inputs are center of base, radius of base, then height.

2. Step 2: Match the inputs to the required dimensions

   CONE
   Specify center of base: 0,0,0
   Specify radius of base: 4
   Specify height: 9

   correctly specifies center (0,0,0), radius 4, and height 9 in the right order.

3. Final Answer:

   Correct command and input order for cone creation -> Option A

4. Quick Check:

   CONE command with center, radius, height =

   CONE
   Specify center of base: 0,0,0
   Specify radius of base: 4
   Specify height: 9

   [OK]

Hint: Follow command input order: center, radius, height [OK]

Common Mistakes:

• Swapping radius and height
• Using CYLINDER command for cone
• Wrong input order