OFFSET command in AutoCAD - Cell-by-Cell Formula Trace

Sample Data

This data represents two lines in AutoCAD with their lengths and the offset distance to create a parallel line.

Cell	Value
A1	Line1
A2	Length: 10
A3	Offset Distance: 2
B1	Line2
B2	Length: 10
B3	Offset Distance: 2

Formula Trace

OFFSET(Line1, 2)

Step 1: Identify original line Line1 with length 10

Step 2: Determine offset distance = 2 units

Step 3: Create new line parallel to Line1 at 2 units distance

Cell Reference Map

   A       B
1 Line1   Line2
2 Len:10  Len:10
3 Off:2   Off:2

Arrows: Line1 --OFFSET(2)--> Line2

Line1 in column A is offset by 2 units to create Line2 in column B.

Result

   A       B
1 Line1   Line2
2 Len:10  Len:10
3 Off:2   Off:2

Result: Line2 is a parallel line to Line1, shifted by 2 units.

The OFFSET command result is shown as Line2, parallel and 2 units away from Line1.

Sheet Trace Quiz - 3 Questions

What does the OFFSET command do to Line1 with distance 2?

A Creates a parallel line 2 units away

B Changes the length of Line1 to 2

C Deletes Line1

D Rotates Line1 by 2 degrees

Key Result

OFFSET(original_object, distance) creates a parallel object at the specified distance.

Practice

1. What does the OFFSET command do in AutoCAD?

easy

A. Creates a parallel copy of an object at a specified distance

B. Deletes the selected object

C. Changes the color of an object

D. Rotates the object around a point

Solution

1. Step 1: Understand the purpose of OFFSET

   The OFFSET command is designed to create a copy of an object parallel to the original at a set distance.

2. Step 2: Compare with other commands

   Deleting, changing color, or rotating are different commands and do not describe OFFSET.

3. Final Answer:

   Creates a parallel copy of an object at a specified distance -> Option A

4. Quick Check:

   OFFSET = parallel copy [OK]

Hint: OFFSET makes parallel copies at set distances [OK]

Common Mistakes:

• Confusing OFFSET with DELETE command
• Thinking OFFSET changes object color
• Assuming OFFSET rotates objects

2. Which is the correct sequence to use the OFFSET command in AutoCAD?

easy

A. Specify distance, select object, choose side

B. Choose side, select object, specify distance

C. Select object, specify distance, choose side

D. Select object, choose side, specify distance

Solution

1. Step 1: Recall OFFSET command steps

   First, you select the object to offset, then specify the distance, and finally choose the side to place the offset.

2. Step 2: Verify the order

   The correct order is select object, specify distance, then choose side. Other orders do not match the command flow.

3. Final Answer:

   Select object, specify distance, choose side -> Option C

4. Quick Check:

   Object -> Distance -> Side [OK]

Hint: Select object first, then distance, then side [OK]

Common Mistakes:

• Specifying distance before selecting object
• Choosing side before selecting object
• Mixing up the order of steps

3. Given a line segment of length 10 units, if you use OFFSET with distance 2 units to the right side, what will be the length of the new line?

medium

A. 12 units

B. 10 units

C. 8 units

D. Cannot determine without angle

Solution

1. Step 1: Understand OFFSET effect on length

   OFFSET creates a parallel copy at a set distance but does not change the length of the original object.

2. Step 2: Apply to the line segment

   The new line will be parallel and same length (10 units), just shifted 2 units to the right.

3. Final Answer:

   10 units -> Option B

4. Quick Check:

   Length unchanged by OFFSET [OK]

Hint: OFFSET copies length unchanged, only shifts position [OK]

Common Mistakes:

• Assuming length increases by offset distance
• Thinking offset changes object size
• Confusing offset distance with length

4. You tried to use the OFFSET command but AutoCAD gave an error. Which of these is the most likely cause?

medium

A. You entered a negative distance value

B. You did not select an object before specifying distance

C. You chose the wrong side to offset

D. You specified zero as the offset distance

Solution

1. Step 1: Check valid distance values

   OFFSET distance must be a positive non-zero number; zero distance is invalid and causes errors.

2. Step 2: Analyze other options

   Negative distances are allowed to offset in opposite direction; selecting object before distance is not required; side choice does not cause errors.

3. Final Answer:

   You specified zero as the offset distance -> Option D

4. Quick Check:

   Zero distance causes error [OK]

Hint: Offset distance cannot be zero [OK]

Common Mistakes:

• Using zero as offset distance
• Thinking negative distance is invalid
• Not selecting object first (allowed)
• Believing side choice causes errors

5. You want to create a wall border 0.5 meters thick around a rectangular floor plan using the OFFSET command. The floor plan is a closed polyline. Which steps should you follow to achieve this correctly?

hard

A. Use OFFSET with 0.5 distance, select the polyline, then pick outside side

B. Use OFFSET with 0.5 distance, select the polyline, then pick inside side

C. Use OFFSET with 1.0 distance, select the polyline, then pick outside side

D. Use OFFSET with 0.5 distance, select each line separately, then pick outside side

Solution

1. Step 1: Set correct offset distance

   The wall thickness is 0.5 meters, so OFFSET distance should be 0.5.

2. Step 2: Select the entire floor plan polyline

   Selecting the closed polyline ensures the offset creates a border around the whole shape.

3. Step 3: Choose the outside side

   To create a border around the floor, offset must be outside the original polyline.

4. Final Answer:

   Use OFFSET with 0.5 distance, select the polyline, then pick outside side -> Option A

5. Quick Check:

   Offset 0.5 outside polyline for wall border [OK]

Hint: Offset closed shape outside by wall thickness [OK]

Common Mistakes:

• Offsetting inside instead of outside
• Using wrong offset distance
• Offsetting lines separately instead of whole polyline