Reading a potentiometer in Arduino - Mini Project: Build & Apply

Reading a potentiometer

📖 Scenario: You have a potentiometer, which is a knob that changes resistance. Turning it changes the voltage that an Arduino can read. We want to read this value and see it in the serial monitor.

🎯 Goal: Build a simple Arduino program that reads the potentiometer value from analog pin A0 and prints it to the serial monitor.

📋 What You'll Learn

Create a variable to store the analog pin number connected to the potentiometer.

Initialize serial communication at 9600 baud.

Read the analog value from the potentiometer using analogRead.

Print the read value to the serial monitor.

💡 Why This Matters

🌍 Real World

Potentiometers are used in many devices to control volume, brightness, or other settings by turning a knob.

💼 Career

Understanding how to read analog sensors like potentiometers is essential for embedded systems and hardware programming jobs.

1

Set up the potentiometer pin

Create an integer variable called potPin and set it to A0 to represent the analog pin connected to the potentiometer.

Arduino

# Create an integer variable called potPin and set it to A0
# Your code here

Hint

Use int potPin = A0; to assign the analog pin.

2

Start serial communication

Add void setup() function and inside it, start serial communication at 9600 baud using Serial.begin(9600);.

Arduino

int potPin = A0;

// Add setup function to start serial communication
// Your code here

Hint

Use void setup() { Serial.begin(9600); } to start serial communication.

3

Read the potentiometer value

Add void loop() function. Inside it, create an integer variable called potValue and set it to the result of analogRead(potPin).

Arduino

int potPin = A0;

void setup() {
  Serial.begin(9600);
}

// Add loop function to read potentiometer value
// Your code here

Hint

Use int potValue = analogRead(potPin); inside loop() to read the value.

4

Print the potentiometer value

Inside the loop() function, add a line to print potValue to the serial monitor using Serial.println(potValue);. Add a small delay of 200 milliseconds after printing.

Arduino

int potPin = A0;

void setup() {
  Serial.begin(9600);
}

void loop() {
  int potValue = analogRead(potPin);
  // Print potValue and add delay
  // Your code here
}

Hint

Use Serial.println(potValue); and delay(200); inside loop().

Practice

1. What does the analogRead(pin) function do when reading a potentiometer on Arduino?

easy

A. It reads the voltage level on the analog pin and returns a value from 0 to 1023.

B. It sets the output voltage of the pin to control the potentiometer.

C. It converts a digital signal to an analog voltage.

D. It resets the potentiometer to zero position.

Solution

1. Step 1: Understand analogRead function

   The analogRead(pin) reads the voltage on the specified analog pin and converts it to a number between 0 and 1023.

2. Step 2: Relate to potentiometer reading

   Since a potentiometer outputs a variable voltage depending on its position, analogRead returns a value representing that voltage level.

3. Final Answer:

   It reads the voltage level on the analog pin and returns a value from 0 to 1023. -> Option A

4. Quick Check:

   analogRead() returns 0-1023 value [OK]

Hint: Remember analogRead returns 0-1023 for voltage levels [OK]

Common Mistakes:

• Thinking analogRead sets voltage instead of reading it
• Confusing analogRead with digitalRead
• Assuming analogRead returns voltage in volts

2. Which of the following is the correct syntax to read a potentiometer connected to analog pin A0 and store the value in a variable named sensorValue?

easy

A. sensorValue = analogWrite(A0);

B. sensorValue = digitalRead(A0);

C. sensorValue = analogRead(A0);

D. sensorValue = readAnalog(A0);

Solution

1. Step 1: Identify correct function for analog input

   The function to read analog input is analogRead(pin), not digitalRead or analogWrite.

2. Step 2: Check variable assignment syntax

   Assigning the result of analogRead(A0) to sensorValue uses the syntax: sensorValue = analogRead(A0);

3. Final Answer:

   sensorValue = analogRead(A0); -> Option C

4. Quick Check:

   Use analogRead() to read analog pin [OK]

Hint: Use analogRead(pin) to read analog sensors [OK]

Common Mistakes:

• Using digitalRead instead of analogRead
• Using analogWrite which is for output
• Using a non-existent function readAnalog

3. What will be printed on the Serial Monitor when the following Arduino code runs and the potentiometer is turned to mid position?

void setup() {
  Serial.begin(9600);
}

void loop() {
  int sensorValue = analogRead(A0);
  Serial.println(sensorValue);
  delay(1000);
}

medium

A. A value close to 0 printed every second

B. A value close to 1023 printed every second

C. No output because Serial.begin is missing

D. A value close to 512 printed every second

Solution

1. Step 1: Understand analogRead output range

   The potentiometer at mid position outputs about half the voltage, so analogRead(A0) returns around 512 (half of 1023).

2. Step 2: Analyze Serial output

   The code prints the sensorValue every 1000 milliseconds (1 second), so the Serial Monitor shows a value near 512 each second.

3. Final Answer:

   A value close to 512 printed every second -> Option D

4. Quick Check:

   Mid potentiometer = ~512 output [OK]

Hint: Mid potentiometer gives about half max value 512 [OK]

Common Mistakes:

• Expecting 0 or 1023 at mid position
• Forgetting Serial.begin causes no output
• Confusing analogRead with digitalRead values

4. The following code is intended to read a potentiometer and print its value, but it does not work correctly. What is the error?

void setup() {
  Serial.begin(9600);
}

void loop() {
  int sensorValue;
  sensorValue = analogRead(0);
  Serial.print(sensorValue);
  delay(500);
}

medium

A. Missing Serial.println instead of Serial.print

B. Serial.begin baud rate is too low

C. No delay after Serial.print

D. Using analogRead(0) instead of analogRead(A0)

Solution

1. Step 1: Check Serial output method

   The code uses Serial.print(sensorValue) without a newline, causing consecutive values to print on the same line and appear garbled or unreadable.

2. Step 2: Use println for readability

   Serial.println(sensorValue) adds a newline after each value, making the output clear on the Serial Monitor.

3. Final Answer:

   Missing Serial.println instead of Serial.print -> Option A

4. Quick Check:

   Serial.print vs println for newlines [OK]

Hint: Use Serial.println() not print() for readable output [OK]

Common Mistakes:

• Using numeric 0 instead of A0 for analogRead
• Confusing Serial.print and Serial.println
• Ignoring delay causing fast output

5. You want to read a potentiometer and map its 0-1023 value to a 0-255 range to control LED brightness using PWM on pin 9. Which code snippet correctly does this?

hard

A. int sensorValue = analogRead(9);
int brightness = map(sensorValue, 0, 255, 0, 1023);
analogWrite(A0, brightness);

B. int sensorValue = analogRead(A0);
int brightness = map(sensorValue, 0, 1023, 0, 255);
analogWrite(9, brightness);

C. int sensorValue = digitalRead(A0);
int brightness = sensorValue * 255;
analogWrite(9, brightness);

D. int sensorValue = analogRead(A0);
int brightness = sensorValue / 4;
digitalWrite(9, brightness);

Solution

1. Step 1: Read potentiometer value correctly

   Use analogRead(A0) to get a value from 0 to 1023.

2. Step 2: Map value to 0-255 for PWM

   Use map(sensorValue, 0, 1023, 0, 255) to convert the range for LED brightness.

3. Step 3: Write PWM value to LED pin

   Use analogWrite(9, brightness) to set LED brightness on pin 9.

4. Final Answer:

   int sensorValue = analogRead(A0); int brightness = map(sensorValue, 0, 1023, 0, 255); analogWrite(9, brightness); -> Option B

5. Quick Check:

   Read analog, map range, write PWM [OK]

Hint: Use map() to convert 0-1023 to 0-255 for PWM [OK]

Common Mistakes:

• Using digitalRead instead of analogRead
• Writing PWM to analog pin or wrong pin
• Using digitalWrite for PWM control