Standby mode behavior in Embedded C

Introduction

Standby mode helps save power by putting the device into a very low energy state when it is not active.

When a device needs to save battery during long idle times.

In wearable devices that must last many hours without charging.

For sensors that only need to wake up occasionally to take measurements.

In remote controls that wait for user input but should use minimal power.

When a system must quickly resume full operation after sleeping.

Syntax

Embedded C

void enter_standby_mode(void) {
    // Prepare device for standby
    // Configure wake-up sources
    // Enter standby mode instruction
}

The exact code to enter standby mode depends on the microcontroller used.

Wake-up sources must be configured before entering standby to resume operation.

Examples

This example shows how to enter standby mode on an STM32 by setting specific registers and then waiting for an interrupt.

Embedded C

/* Example for STM32 microcontroller */
PWR->CR |= PWR_CR_PDDS; // Set Power Down Deep Sleep
SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk; // Set SLEEPDEEP bit
__WFI(); // Wait For Interrupt to enter standby

A simplified example where functions handle wake-up setup and entering standby.

Embedded C

/* Example for generic MCU */
set_wakeup_source();
enter_standby();

Sample Program

This program simulates entering standby mode by setting flags and printing messages. In a real embedded system, the __WFI() instruction would put the CPU to sleep until an interrupt wakes it.

Embedded C

#include <stdint.h>
#include <stdio.h>

// Simulated registers for demonstration
volatile uint32_t PWR_CR = 0;
volatile uint32_t SCB_SCR = 0;

#define PWR_CR_PDDS (1 << 1)
#define SCB_SCR_SLEEPDEEP_Msk (1 << 2)

void enter_standby_mode(void) {
    printf("Preparing to enter standby mode...\n");
    PWR_CR |= PWR_CR_PDDS; // Set power down deep sleep
    SCB_SCR |= SCB_SCR_SLEEPDEEP_Msk; // Set sleep deep bit
    printf("Standby mode entered. Waiting for interrupt...\n");
    // __WFI(); // In real MCU, this would wait for interrupt
}

int main(void) {
    printf("System running normally.\n");
    enter_standby_mode();
    printf("System woke up from standby.\n");
    return 0;
}

Important Notes

Standby mode usually stops most clocks and reduces power to peripherals.

Wake-up sources can be buttons, timers, or external signals.

Always configure wake-up sources before entering standby to avoid being stuck.

Summary

Standby mode saves power by putting the device into a deep sleep state.

You must set specific registers and configure wake-up sources before entering standby.

The device wakes up when a configured event or interrupt occurs.

Practice

1. What is the main purpose of putting a microcontroller into standby mode?

easy

A. To save power by entering a deep sleep state

B. To increase the clock speed temporarily

C. To reset all registers to default values

D. To enable all peripherals for faster processing

Solution

1. Step 1: Understand standby mode function

   Standby mode is designed to reduce power consumption by putting the device into a very low power state.

2. Step 2: Compare options with standby purpose

   Only To save power by entering a deep sleep state correctly describes saving power by deep sleep. Other options describe unrelated functions.

3. Final Answer:

   To save power by entering a deep sleep state -> Option A

4. Quick Check:

   Standby mode = power saving [OK]

Hint: Standby mode means deep sleep to save power [OK]

Common Mistakes:

• Confusing standby with reset or speed boost
• Thinking standby enables all peripherals
• Assuming standby clears registers

2. Which of the following code snippets correctly sets the microcontroller to enter standby mode in embedded C?

easy

A. PWR->CR &= ~PWR_CR_PDDS; SCB->SCR &= ~SCB_SCR_SLEEPDEEP_Msk; __WFI();

B. PWR->CR |= PWR_CR_PDDS; SCB->SCR &= ~SCB_SCR_SLEEPDEEP_Msk; __WFI();

C. PWR->CR |= PWR_CR_CWUF; SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk; __WFE();

D. PWR->CR |= PWR_CR_PDDS; SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk; __WFI();

Solution

1. Step 1: Identify correct register settings for standby

   Setting PWR_CR_PDDS bit and SLEEPDEEP bit enables standby mode deep sleep.

2. Step 2: Check the wait instruction

   __WFI() (Wait For Interrupt) is used to enter sleep mode properly.

3. Final Answer:

   PWR->CR |= PWR_CR_PDDS; SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk; __WFI(); -> Option D

4. Quick Check:

   Set PDDS + SLEEPDEEP + __WFI() = standby [OK]

Hint: Set PDDS and SLEEPDEEP bits, then call __WFI() [OK]

Common Mistakes:

• Clearing PDDS or SLEEPDEEP bits disables standby
• Using __WFE() instead of __WFI() incorrectly
• Not setting SLEEPDEEP bit before sleep

3. Given the code below, what will be the output after the microcontroller wakes up from standby mode?

volatile int flag = 0;
void enter_standby() {
  PWR->CR |= PWR_CR_PDDS;
  SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk;
  __WFI();
  flag = 1;
}

int main() {
  enter_standby();
  if(flag) {
    printf("Woke up from standby\n");
  } else {
    printf("Still running\n");
  }
  return 0;
}

medium

A. Woke up from standby

B. Compilation error due to volatile variable

C. Still running

D. No output (program stuck in standby)

Solution

1. Step 1: Understand standby mode effect on program flow

   Standby mode resets the device on wake-up, so code after __WFI() is not executed.

2. Step 2: Analyze flag variable and output

   Since flag is set after __WFI(), but device resets, flag remains 0 and main restarts, so output will be "Still running" because flag is 0 after reset.

3. Final Answer:

   Still running -> Option C

4. Quick Check:

   Standby resets device, code after __WFI() not run, flag remains 0 [OK]

Hint: Standby resets device; code after __WFI() won't run [OK]

Common Mistakes:

• Assuming code after __WFI() runs after wake-up
• Ignoring device reset on standby wake-up
• Confusing volatile with persistence across reset

4. Identify the error in the following code snippet that prevents the microcontroller from entering standby mode:

void enter_standby() {
  PWR->CR |= PWR_CR_PDDS;
  SCB->SCR &= ~SCB_SCR_SLEEPDEEP_Msk;
  __WFI();
}

medium

A. PDDS bit is not set correctly

B. SLEEPDEEP bit is cleared, so device does not enter deep sleep

C. __WFI() is the wrong instruction to enter standby

D. Missing enabling of power clock before setting registers

Solution

1. Step 1: Check SLEEPDEEP bit usage

   SLEEPDEEP bit must be set to enter deep sleep (standby). Clearing it disables deep sleep.

2. Step 2: Verify other settings

   PDDS bit is set correctly; __WFI() is correct; power clock enabling is not shown but not always mandatory here.

3. Final Answer:

   SLEEPDEEP bit is cleared, so device does not enter deep sleep -> Option B

4. Quick Check:

   SLEEPDEEP cleared = no deep sleep [OK]

Hint: SLEEPDEEP bit must be set for standby mode [OK]

Common Mistakes:

• Clearing SLEEPDEEP bit disables standby
• Confusing __WFI() with __WFE()
• Forgetting to set PDDS bit

5. You want to configure a microcontroller to enter standby mode but wake up only when a specific external interrupt occurs. Which sequence correctly achieves this behavior?

hard

A. Enable external interrupt line; configure wake-up pin; set PDDS and SLEEPDEEP bits; call __WFI()

B. Set PDDS and SLEEPDEEP bits; call __WFI(); enable external interrupt after wake-up

C. Call __WFI(); then set PDDS and SLEEPDEEP bits; enable external interrupt

D. Enable external interrupt; call __WFE(); clear PDDS bit; set SLEEPDEEP bit

Solution

1. Step 1: Configure wake-up source before standby

   External interrupt line and wake-up pin must be enabled before entering standby.

2. Step 2: Set standby mode bits and enter sleep

   Set PDDS and SLEEPDEEP bits to enable standby, then call __WFI() to enter standby mode.

3. Final Answer:

   Enable external interrupt line; configure wake-up pin; set PDDS and SLEEPDEEP bits; call __WFI() -> Option A

4. Quick Check:

   Setup wake-up + set bits + __WFI() = standby with wake-up [OK]

Hint: Setup wake-up source before standby, then set bits and __WFI() [OK]

Common Mistakes:

• Enabling interrupts after entering standby
• Clearing PDDS bit disables standby
• Using __WFE() without proper wake-up config