I2C acknowledge and NACK behavior in Embedded C

Introduction

I2C acknowledge (ACK) and not acknowledge (NACK) signals help devices talk clearly. They tell the sender if the receiver got the data or not.

When checking if a device on the I2C bus is ready to communicate.

When sending data bytes and confirming the receiver accepted them.

When ending communication to signal no more data will be sent.

When debugging communication problems between microcontrollers and sensors.

Syntax

Embedded C

void I2C_SendAck(void);
void I2C_SendNack(void);

ACK means the receiver says 'I got your data'.

NACK means the receiver says 'I did not get your data' or 'stop sending'.

Examples

This tells the sender to continue sending data.

Embedded C

I2C_SendAck(); // Send ACK after receiving a byte

This tells the sender to stop sending data.

Embedded C

I2C_SendNack(); // Send NACK after last byte

Sample Program

This program simulates receiving three bytes over I2C. It sends ACK after the first two bytes to say 'keep sending'. After the last byte, it sends NACK to say 'stop'.

Embedded C

#include <stdio.h>

// Simulated functions for ACK and NACK
void I2C_SendAck(void) {
    printf("ACK sent\n");
}

void I2C_SendNack(void) {
    printf("NACK sent\n");
}

int main() {
    // Simulate receiving 3 bytes
    for (int i = 0; i < 2; i++) {
        printf("Byte %d received\n", i+1);
        I2C_SendAck(); // Acknowledge each byte except last
    }
    printf("Byte 3 received\n");
    I2C_SendNack(); // NACK after last byte to stop
    return 0;
}

Important Notes

Always send ACK after receiving data if you want more data.

Send NACK to signal the end of data or if an error occurs.

Missing ACK or NACK can cause the I2C bus to hang or misbehave.

Summary

ACK means 'I received your data, send more.'

NACK means 'Stop sending, I am done or there is a problem.'

Use ACK and NACK to control smooth communication on the I2C bus.

Practice

1. What does an ACK (Acknowledge) signal mean in I2C communication?

easy

A. The sender is requesting to resend the data

B. The receiver wants to stop communication immediately

C. The communication line is idle

D. The receiver successfully received data and is ready for more

Solution

1. Step 1: Understand ACK meaning in I2C

   ACK means the receiver signals it has received the data correctly and is ready to continue.

2. Step 2: Compare options with ACK meaning

   Only The receiver successfully received data and is ready for more matches this meaning; others describe stop or errors.

3. Final Answer:

   The receiver successfully received data and is ready for more -> Option D

4. Quick Check:

   ACK = Ready for more data [OK]

Hint: ACK means receiver says 'send more' [OK]

Common Mistakes:

• Confusing ACK with NACK meaning
• Thinking ACK means stop communication
• Assuming ACK means error occurred

2. Which of the following code snippets correctly sends a NACK after reading the last byte in I2C using embedded C?

easy

A. i2c_read_byte(I2C1, ACK);

B. i2c_read_byte(I2C1, NACK);

C. i2c_write_byte(I2C1, NACK);

D. i2c_send_ack(I2C1);

Solution

1. Step 1: Identify correct function to read with NACK

   To signal no more data is needed, the read function must be called with NACK.

2. Step 2: Check options for correct usage

   i2c_read_byte(I2C1, NACK); uses i2c_read_byte with NACK, which is correct. Others either send ACK or write instead of read.

3. Final Answer:

   i2c_read_byte(I2C1, NACK); -> Option B

4. Quick Check:

   Read last byte with NACK to stop [OK]

Hint: Use read with NACK to stop reading last byte [OK]

Common Mistakes:

• Using ACK instead of NACK after last byte
• Calling write instead of read for NACK
• Confusing function names for ACK/NACK

3. Consider this code snippet reading 3 bytes from an I2C device:

for (int i = 0; i < 3; i++) {
  data[i] = (i < 2) ? i2c_read_byte(I2C1, ACK) : i2c_read_byte(I2C1, NACK);
}

What is the purpose of sending NACK on the last byte?

medium

A. To request the device to resend the last byte

B. To acknowledge the last byte and continue reading

C. To indicate the master will stop reading after this byte

D. To reset the I2C bus immediately

Solution

1. Step 1: Analyze the loop and ACK/NACK usage

   The loop reads 3 bytes; for first two bytes it sends ACK, for last byte it sends NACK.

2. Step 2: Understand NACK meaning on last byte

   NACK signals the master will stop reading after this byte, telling the slave no more data is needed.

3. Final Answer:

   To indicate the master will stop reading after this byte -> Option C

4. Quick Check:

   NACK on last byte = stop reading [OK]

Hint: NACK on last byte means stop reading [OK]

Common Mistakes:

• Thinking NACK requests resend
• Assuming NACK resets bus
• Confusing ACK and NACK roles

4. You wrote this code to read bytes from I2C but the slave device never stops sending data:

for (int i = 0; i < 4; i++) {
  data[i] = i2c_read_byte(I2C1, ACK);
}

What is the likely problem?

medium

A. You never sent NACK after the last byte to stop reading

B. You should use i2c_write_byte instead of i2c_read_byte

C. The loop should run 5 times instead of 4

D. You need to send a STOP condition before reading

Solution

1. Step 1: Check ACK/NACK usage in the loop

   The code sends ACK for every byte read, never sending NACK to signal stop.

2. Step 2: Understand effect of missing NACK

   Without NACK after last byte, slave keeps sending data, causing endless transmission.

3. Final Answer:

   You never sent NACK after the last byte to stop reading -> Option A

4. Quick Check:

   Missing NACK means no stop signal [OK]

Hint: Send NACK after last byte to stop slave [OK]

Common Mistakes:

• Using ACK for all bytes including last
• Confusing read and write functions
• Ignoring need for STOP condition after read

5. You want to write a function that reads a variable number of bytes from an I2C device and properly sends ACK for all bytes except the last one, which should send NACK. Which code snippet correctly implements this behavior?

hard

A. for (int i = 0; i < length - 1; i++) {
data[i] = i2c_read_byte(I2C1, ACK);
}
data[length - 1] = i2c_read_byte(I2C1, NACK);

B. for (int i = 0; i < length; i++) {
data[i] = i2c_read_byte(I2C1, ACK);
}

C. for (int i = 0; i < length; i++) {
data[i] = i2c_read_byte(I2C1, NACK);
}

D. data[0] = i2c_read_byte(I2C1, NACK);
for (int i = 1; i < length; i++) {
data[i] = i2c_read_byte(I2C1, ACK);
}

Solution

1. Step 1: Understand ACK/NACK pattern for multiple bytes

   All bytes except last must be read with ACK; last byte with NACK to stop.

2. Step 2: Analyze each option

   for (int i = 0; i < length - 1; i++) { data[i] = i2c_read_byte(I2C1, ACK); } data[length - 1] = i2c_read_byte(I2C1, NACK); reads all but last byte with ACK, then last byte with NACK, correctly signaling stop. Others send wrong signals or in wrong order.

3. Final Answer:

   for (int i = 0; i < length - 1; i++) { data[i] = i2c_read_byte(I2C1, ACK); } data[length - 1] = i2c_read_byte(I2C1, NACK); -> Option A

4. Quick Check:

   ACK all but last, NACK last byte [OK]

Hint: Send NACK only on last byte read [OK]

Common Mistakes:

• Sending NACK on all bytes
• Sending ACK on last byte
• Reading last byte first with NACK